Publicité
Les langues disponibles
Les langues disponibles
TECHNICAL DATA
Type
Production code
Battery voltage
Rated speed
Thread of work spindle
D=Grinding disc diameter max.
d=Grinding disc hole diameter
b=Grinding disc thickness max.
b=Cutting disc thickness max. / min.
D=Sanding disc diameter max.
D=Wiring brush diameter max.
Weight according EPTA-Procedure 01/2014
(Li-Ion 2,0 Ah ... 12,0 Ah)
Recommended Ambient Operating Temperature
Recommended battery types
Recommended charger
Noise information: Measured values determined according to
EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level / Uncertainty K
Sound power level / Uncertainty K
Wear ear protectors!
Vibration information: Vibration total values (triaxial vector
sum) determined according to EN 62841
Vibration emission value a
/ Uncertainty K
h
Surface grinding
Disc sanding
For other applications, e.g. Abrasive Cutting-Off Operations or Wire Brushing other vibration values could occur.
WARNING!
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in
EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration and noise emission may differ. This may significantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it
is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
WARNING!
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
ANGLE GRINDER SAFETY WARNINGS
Safety Warnings Common for Grinding, Sanding, Wire Brus-
hing or Abrasive Cutting-Off Operations:
a) This power tool is intended to function as a grinder,
sander, wire brush or cut-off tool. Read all safety warnings,
instructions, illustrations and specifications provided with
this power tool. Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
20
M18 BLSAG125X
M18 BLSAG115XPD
Cordless Angle Grinder Cordless Angle Grinder Cordless Angle Grinder
4972 15 01
4972 25 01
XXXXXX MJJJJ
XXXXXX MJJJJ
18 V
18 V
11000 min
11000 min
-1
-1
M14
M14
125 mm
115 mm
22,2 mm
22,2 mm
6 mm
6 mm
3 mm / 1 mm
3 mm / 1 mm
125 mm
115 mm
75 mm
75 mm
2,2 ... 3,3 kg
2,2 ... 3,3 kg
-18 ... +50 °C
-18 ... +50 °C
M18B...; M18HB...
M18B...; M18HB...
M12-18...; M1418C6
M12-18...; M1418C6
M12-18...; M1418C6
92,51 dB (A) / 3 dB (A)
92,51 dB (A) / 3 dB (A)
92,51 dB (A) / 3 dB (A)
100,51 dB (A) / 3 dB (A)
100,51 dB (A) / 3 dB (A)
100,51 dB (A) / 3 dB (A)
6,30 m/s² / 1,5 m/s²
7,10 m/s² / 1,5 m/s²
7,10 m/s² / 1,5 m/s²
1,97 m/s² / 1,5 m/s²
1,82 m/s² / 1,5 m/s²
1,82 m/s² / 1,5 m/s²
b) Operations such as polishing are not recommended to be
performed with this power tool. Operations for which the power
tool was not designed may create a hazard and cause personal
injury.
c) Do not convert this power tool to operate in a way which is
not specifically designed and specified by the tool manufac-
turer. Such a conversion may result in a loss of control and cause
serious personal injury.
d) Do not use accessories which are not specifically designed
and recommended by the tool manufacturer. Just because the
accessory can be attached to your power tool, it does not assure
safe operation.
e) The rated speed of the accessory must be at least equal to
the maximum speed marked on the power tool. Accessories
running faster than their rated speed can break and fly apart.
ENGLISH
f) The outside diameter and the thickness of your acces-
M18 BLSAG125XPD
sory must be within the capacity rating of your power tool.
IIncorrectly sized accessories cannot be adequately guarded or
controlled.
4972 35 01
g) The dimensions of the accessory mounting must fit the
XXXXXX MJJJJ
dimensions of the mounting hardware of the power tool.
18 V
Accessories that do not match the mounting hardware of the power
tool will run out of balance, vibrate excessively and may cause loss
11000 min
-1
of control.
M14
h) Do not use a damaged accessory. Before each use inspect
125 mm
the accessory such as abrasive wheels for chips and cracks,
22,2 mm
backing pad for cracks, tear or excess wear, wire brush for
loose or cracked wires. If power tool or accessory is dropped,
inspect for damage or install an undamaged accessory. After
6 mm
inspecting and installing an accessory, position yourself and
bystanders away from the plane of the rotating accessory and
run the power tool at maximum no-load speed for one minute.
3 mm / 1 mm
Damaged accessories will normally break apart during this test time.
i) Wear personal protective equipment. Depending on appli-
cation, use face shield, safety goggles or safety glasses. As
appropriate, wear dust mask, hearing protectors, gloves and
125 mm
workshop apron capable of stopping small abrasive or work-
piece fragments. The eye protection must be capable of stopping
flying debris generated by various applications. The dust mask or
75 mm
respirator must be capable of filtrating particles generated by the
particular application. Prolonged exposure to high intensity noise
may cause hearing loss.
2,2 ... 3,3 kg
j) Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal protective
-18 ... +50 °C
equipment. Fragments of workpiece or of a broken accessory may
M18B...; M18HB...
fly away and cause injury beyond immediate area of operation.
k) Hold the power tool by insulated gripping surfaces only,
when performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting a "live"
wire may make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
l) Never lay the power tool down until the accessory has come
to a complete stop. The spinning accessory may grab the surface
and pull the power tool out of your control.
m) Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could snag your
clothing, pulling the accessory into your body.
n) Regularly clean the power tool's air vents. The motor's fan
will draw the dust inside the housing and excessive accumulation of
powdered metal may cause electrical hazards.
o) Do not operate the power tool near flammable materials.
Sparks could ignite these materials.
p) Do not use accessories that require liquid coolants. Using
water or other liquid coolants may result in electrocution or shock.
Kickback and related warnings:
Kickback is a sudden reaction to a pinched or snagged rotating
wheel, backing pad, brush or any other accessory. Pinching or
snagging causes rapid stalling of the rotating accessory which in
turn causes the uncontrolled power tool to be forced in the direc-
tion opposite of the accessory's rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by the
workpiece, the edge of the wheel that is entering into the pinch
point can dig into the surface of the material causing the wheel to
climb out or kick out. The wheel may either jump toward or away
from the operator, depending on direction of the wheel's movement
at the point of pinching. Abrasive wheels may also break under
these conditions.
Kickback is the result of power tool misuse and/or incorrect opera-
ting procedures or conditions and can be avoided by taking proper
precautions as given below.
a) Maintain a firm grip on the power tool and position your
body and arm to allow you to resist kickback forces. Always
use auxiliary handle, if provided, for maximum control over
kickback or torque reaction during start-up. The operator can
control torque reactions or kickback forces, if proper precautions
are taken.
b) Never place your hand near the rotating accessory. Acces-
sory may kickback over your hand.
c) Do not position your body in the area where power tool will
move if kickback occurs. Kickback will propel the tool in direction
opposite to the wheel's movement at the point of snagging.
d) Use special care when working corners, sharp edges etc.
Avoid bouncing and snagging the accessory. Corners, sharp
edges or bouncing have a tendency to snag the rotating accessory
and cause loss of control or kickback.
e) Do not attach a saw chain woodcarving blade or toothed saw
blade. Such blades create frequent kickback and loss of control.
Safety Warnings Specific for Grinding and Abrasive Cutting-
Off Operations:
a) Use only wheel types that are specified for your power
tool and the specific guard designed for the selected wheel.
Wheels for which the power tool was not designed cannot be
adequately guarded and are unsafe.
b) The grinding surface of the centre depressed wheels must
be mounted below the plane of the guard lip. An improperly
mounted wheel that projects through the plane of the guard lip
cannot be adequately protected.
c) The guard must be securely attached to the power tool and
positioned for maximum safety, so the least amount of wheel
is exposed towards the operator. The guard helps to protect the
operator from broken wheel fragments, accidental contact with
wheel and sparks that could ignite clothing.
d) Wheels must be used only for specified applications. For
example: do not grind with the side of cut-off wheel. Abrasive
cut-off wheels are intended for peripheral grinding, side forces
applied to these wheels may cause them to shatter.
e) Always use undamaged wheel flanges that are of correct
size and shape for your selected wheel. Proper wheel flanges
support the wheel thus reducing the possibility of wheel breakage.
Flanges for cut-off wheels may be different from grinding wheel
flanges.
f) Do not use worn down wheels from larger power tools. A
wheel intended for larger power tool is not suitable for the higher
speed of a smaller tool and may burst.
g) When using dual purpose wheels always use the correct
guard for the application being performed. Failure to use the
correct guard may not provide the desired level of guarding, which
could lead to serious injury.
Additional safety warnings specific for abrasive cutting-off
operations:
a) Do not "jam" the cut-off wheel or apply excessive pressure.
Do not attempt to make an excessive depth of cut. Overstres-
sing the wheel increases the loading and susceptibility to twisting
or binding of the wheel in the cut and the possibility of kickback or
wheel breakage.
b) Do not position your body in line with and behind the rota-
ting wheel. When the wheel, at the point of operation, is moving
away from your body, the possible kickback may propel the spinning
wheel and the power tool directly at you.
c) When wheel is binding or when interrupting a cut for any
reason, switch off the power tool and hold the power tool
motionless until the wheel comes to a complete stop. Never
attempt to remove the cut-off wheel from the cut while the
wheel is in motion otherwise kickback may occur. Investigate
and take corrective action to eliminate the cause of wheel binding.
d) Do not restart the cutting operation in the workpiece. Let
the wheel reach full speed and carefully re-enter the cut. The
wheel may bind, walk up or kickback if the power tool is restarted in
the workpiece.
e) Support panels or any oversized workpiece to minimize the
risk of wheel pinching and kickback. Large workpieces tend to
sag under their own weight. Supports must be placed under the
workpiece near the line of cut and near the edge of the workpiece
on both sides of the wheel.
ENGLISH
21
Publicité
