Publicité
To ensure that the seat is correctly and securely
connected at both points – (H4) and (I), push the
seat firmly forward and pull it firmly backward to
make sure that the connection was successful.
Both action points (I1) and (J) are red for your
awareness.
5. The child seat has a centre of gravity (F) (inscribed
on the child seat) that must be positioned in front of
the rear wheel axle. If it is positioned behind the axle,
the distance must not exceed 10 cm. Special care
must also be taken when positioning the child seat
to ensure that the cyclist does not touch the child
seat with his feet when cycling. Note: In Germany,
according to the German Traffic Law StVZO, bicycle
seats may only be fixed so that 2/3 of the seat depth
How to safely place and secure the child on the seat
1. To safely place the child on the seat you must place
the bicycle on flat and solid ground for maximum
bicycle stability. Even if your bicycle offers robust
quick stands, you must always hold the bicycle, while
placing/ removing the child. You must carry your
child in your lap and safely place him on the seat. It´s
forbidden for the child to climb alone on the bicycle
or using the footrests to reach the seat. To place
the child in the seat, first fully extend the retention
system harness (B), by pressing the adjuster button
(B2.1) of the belt guide (B2), then pull it up - this
makes it easier to put the child in the seat. Then, open
the safety buckle (B1) by pressing the safety buckle
button. After releasing the buckle, detach both sides
by sliding one up and the other down. Seat the child,
place the shoulder straps and then connect it by
sliding the two parts of the buckle together and close
the safety buckle. Before fastening the buckle, ensure
that both sides are securely connected. Close the
safety buckle, adjust the belt length using the strap
adjusters, so that your child is securely restrained.
Before starting the journey, always check that the
How to Remove the Seat from the Bicycle Frame (1P)
OPTION A - REMOVE THE BABY SEAT + BASE +
METALLIC SUPPORT BAR
1. Detach the safety-belt (C) in order to remove the
baby seat. Then press the block button (K3) of the
metallic bracket (K) and simultaneously pull the
metallic support bar (L) up and back as shown in the
image.
How to Remove the Seat from the Bicycle Luggage Carrier (E-BD)
1. Detach the safety-belt (C) in order to remove the
child bicycle seat.
1. Press the button to unlock the padlock. While
pressing the button, set and save your new code.
Close the padlock. Change the numbering to hide
your new code. To unlock the padlock, simply enter
your new code again, and then press the button.
Please make sure that the padlock is always kept
away. Note: The lock should only be used when the
bike is parked and not in use as an anti-theft device.
How to set your Bobike padlock
or the Gravity Center of the seat is located between
the front and rear axle of the bicycle.
6. Shake the seat (A) and apply forward pressure as
well as backward pulling to verify that all mounting
systems are securely fastened, and the seat is
firmly attached to each of them. Conducting this
verification is of utmost importance for the safety of
both the cyclist and the child.
7. Start to open the safety belt buckle (C1) and pass it
around the bicycle frame. Adjust the belt it as shown
in the picture, under tension. Make sure that remain
loosen belt is not in contact with the wheel, so pass
it through the Safety belt retainer (C2). This step is
extremely important for the cyclist and child safety.
child is secured and that the belt is snug but not so
tight that it hurts the child. According to the child
growth, current height, and weight, you can adjust
the height of the retention system harness (B) on all
the strap adjusters (B2), by pulling up or down the
straps until reaching the desired size.
2. Adjust the height of the footrest according to the
size of the child. To do this, raise the lever (E1) and
slide it up or down for the required height. After
deciding on the correct height, lower the lever (E1)
to lock in place.
3. To remove the footrest strap (E3), lift it slightly
to release it from the footrest peg (E2) and slide it
upwards to disengage it from the footrest slot. Then
pass the thin end of the plastic strap through the
hole in the footrest, as shown in the picture. Once the
strap is correctly positioned, it can be easily slid up or
down according to the child's foot. Next slot one of
the openings in the strap over the foot support peg. If
you want to remove the strap (E3), twist it slightly to
loosen it from the foot support peg (E2).
OPTION B - REMOVE THE BABY SEAT FROM
THE BASE, LEAVING THE SUPPORT BAR + BASE
INSTALLED ON THE BICYCLE
1. Detach the safety-belt (C) in order to remove the
baby seat.
2. Press the jaws (I) and pull both of them out. At the
same time, pull the baby seat up and back.
2. Press the jaws (I) and pull both of them out. At the
same time, pull the baby seat up and back.
Ensure the padlock is stored in a secure location, out
of children's reach, to prevent potential strangulation
hazards. Keep the padlock close and under adult
supervision when in use, such as attaching it to a
belt loop or keeping it in a secured pocket. Following
these technical measures can help mitigate the risk
of strangulation and ensure the padlock is used safely
and responsibly.
6
Publicité
