Bobike One Maxi 1P & E-BD Instructions De Montage page 51

page de 174

/ 174
Signets

Speciﬁc Instructions for Mounting the Seat in the Frame of your Bicycle (1P)

1. Remove the metallic bracket (K) from the metallic

support bar (L). To do that, you should press the

metallic bracket button (K3) and simultaneously pull

the metallic support bar (L) up.

2. Remove the screws (K1) on the metallic bracket (K),

with the Allen key No. 5 (N).

3. The correct positioning of the metallic bracket (K)

is extremely important. Make sure it is positioned

in the bicycle frame according to the picture - from

the front and assembled on the seat tube and never

assembled on the seat post. Place the body of the

front mounting block (K2) on the bicycle frame from

the front. Insert 4 screws (K1) in the block to tighten

the rear metallic mounting plate (K4). Tighten the

screws, with the Key (N), so that the metallic bracket

(K) is secured but not fully tightened so that, if

necessary, you can adjust the height later. However,

note that it should be tight to make it easier to

complete the next step. You need to tighten the 4

screws diagonally and in stages.

4. Place the edges of the metallic support bar (L)

at the holes of the metallic bracket (K) until you

hear a click indicating the lock, and until the centre

button (K3) shall be level with the exterior of the

hose metallic bracket. Centre and adjust the metallic

support bar (L) at a height above the rear wheel, so

that later, when you add the weight of the child, the

child bicycle seat does not touch the wheel. Note that

the metallic support bar (L) should be positioned at a

maximum of 10cm away from the wheel. Never use

the metallic support bar (L) to carry other loads than

this child seat, as indicated in this manual.

5. Press the jaws button (I1) downward and pull

outward to unlock the base (H). Pull the base (H)

outward to detach it from the seat (A).

6. Freeing the metallic clamps (H2) is necessary. To

achieve this, utilize the Allen key nrº5 (N) to relieve

only, in cross, the (H1) screws. Then also relieve the

screws (H3).

7. Ensure the base (H) is centered diagonally and

vertically on the metallic support bar (L). If the base

shifts during tightening, re-center it to maintain

proper alignment. Proper centering of the base

is crucial for child/adult safety. Proceed assuring

that the front metallic clamps (H2), close to Bobike

logo, are positioned between the designated space

limiters (L1) indicated by the arrow in the Quick-

Guide picture. Do not place the front metallic clamps

(H2) outside this area and notice that the seat shall

be installed as close to the saddle as possible. While

Speciﬁc Instructions for Mounting the Seat in the Luggage Carrier of your Bicycle (E-BD)

1. Press the jaws button (I1) downward and pull

outward to unlock the base (H). Pull the base (H)

outward to detach it from the seat (A).

2. Freeing the metallic clamps (H2) is necessary. To

achieve this, utilize the Allen key nrº5 (N) to relieve

only, in cross, the (H1) screws. Then also relieve the

screws (H3).

3. Ensure the base is centred on the luggage carrier.

If the base shifts during tightening, re-center it

to maintain proper alignment. While assuring

center alignment with the luggage carrier, start by

tightening the two screws (H3) with a torque of 2

assuring center alignment with the support bar (L),

start by tightening the two screws (H3) with a torque

of 2 N.m. Next, tighten the four screws (H1) in a cross

pattern with the Allen Key (N). Apply suﬃcient torque

6 N.m to securely fasten the base to the support bar

(L).

8. Please note that the safety of the child/adult

is of paramount importance when following this

step. Hold the safety belt (C). Make sure that you

ﬁrst ﬁt the red metal connector device (J) into

the corresponding slot (H4) of the base (H) near

the Bobike Logo. Then, pull the seat down ﬁrmly

so that the claws (I) connect fully to the base (H).

When you do this correctly you will hear 2 clicks.

To ensure that the seat is correctly and securely

connected at both points – (H4) and (I), push the

seat ﬁrmly forward and pull it ﬁrmly backward to

make sure that the connection was successful.

Both action points (I1) and (J) are red for your

awareness.

9. The child seat has a centre of gravity (F) (inscribed

on the child seat) that must be positioned in front of

the rear wheel axle. If it is positioned behind the axle,

the distance must not exceed 10 cm. Special care

must also be taken when positioning the child seat

to ensure that the cyclist does not touch the child

seat with his feet when cycling. Note: In Germany,

according to the German Traﬃc Law StVZO, bicycle

seats may only be ﬁxed so that 2/3 of the seat depth

or the Gravity Center of the seat is located between

the front and rear axle of the bicycle.

10. After adjusting the height and positioning of

the seat (A), hand tighten with the Allen Key (N) the

metallic bracket (K) to ensure that it cannot move.

You need to hand tight the screws (K1) diagonally,

with the same force and in stages, with a torque of

8 N.m.

11. Shake the seat (A) and apply forward pressure as

well as backward pulling to verify that all mounting

systems are securely fastened, and the seat is

ﬁrmly attached to each of them. Conducting this

veriﬁcation is of utmost importance for the safety of

both the cyclist and the child.

12. Start to open the safety belt buckle (C1) and

pass it around the bicycle frame. Adjust the belt it as

shown in the picture, under tension. Make sure that

remain loosen belt is not in contact with the wheel,

so pass it through the Safety belt retainer (C2). This

step is extremely important for the cyclist and child

safety.

N.m. Next, tighten the four screws (H1) in a cross

pattern with the Allen Key (N). Apply suﬃcient torque

6 N.m to securely fasten the base to the luggage

carrier.

4. Please note that the safety of the child/adult