Publicité
Rear child seat for bicycle
A. Main seat
B. Retention system harness
B1. Safety buckle
B2. Height strap adjusters
B2.1. Adjustment button
C. Safety belt for bicycle frame
C1. Safety belt buckle
C2. Safety belt retainer
D. Back reflector
E. Footrest
E1. Footrest lever
E2. Footrest peg
E3. Footrest strap
F. Center of gravity
G. Seat cushion
I. Opening and clamping jaw
I1. Jaw button
J. Red safety connector device
M. Traceability information
N. Allen key nrº 5
This product contains small parts like bolts, plastic bags, and small packaging hangers. Keep them out of
reach of children to avoid suffocation hazards.
• This child bicycle seat must not be mounted in
folding bicycles.
• This child bicycle seat must not be used on EPAC /
Pedelecs above 25 km/h / 15,5mph.
• This child bicycle seat must not be mounted to
bicycles fitted with rear shock absorbers.
• This child bicycle seat must not be mounted to
motorized vehicles such as mopeds, scooters.
• This child bicycle seat is only suitable for carrying
children with a maximum weight of 22 Kg, and a
maximum height of 110 cm, (and children with
recommended ages ranging from 9 months to
6 years of age - with the weight and height as the
decisive variable).
• The total weight of the cyclist and the child
transported must not exceed the maximum
permitted load permitted for the bicycle. Information
on the maximum load can be found in the operating
instructions of the bicycle. You can also contact the
manufacturer for this question.
• The seat may only be mounted on a bicycle suitable
for the attachment of such additional loads. Please
consult your bicycle instructions manual.
• The position of the child bicycle seat must be
adjusted so that the bicycle rider does not touch the
child bicycle seat with the feet when in motion.
• It's very important to adjust correctly the seat and
its component parts for optimum comfort and safety
of the child. It's also important that the seat does not
slope forward, so that the child does not tend to slide
One Maxi 1P&E-BD
Table of Contents of Product
ATTENTION
Specific Instructions For Mounting
EN.
Frame Mounting System (1P)
H. Seat mounting base
H1. 4 x screws
H2. 4 x metallic clamps
H3. 2 x screws
H4. Insertion opening for the metallic protection system
K. Metallic bracket
K1. 4 x screws
K2. Front mounting block
K3. Block button
K4. Rear metallic mounting plate
L. Metallic support bar
L1. Limiters of the clamps
Carrier Mounting System (E-BD)
H. Seat mounting base
H1. 4 x screws
H2. 4 x metallic clamps
H3. 2 x screws
H4. Insertion opening for the metallic protection system
out of it. It is also important that the backrest slope
backward slightly.
• Check if all parts of the bicycle function correctly
with the child bicycle seat mounted.
• Check the instructions of the bicycle, and If you
have any doubts on fitting the child bicycle seat to
your bicycle, please contact your bicycle supplier for
further information.
Specific instructions to assemble your seat on the frame
of your bicycle (1P)
• This child bicycle seat must be assembled on
bicycles with round and oval frames with diameters
ranging from Ø28 to Ø40 mm.
• The child bicycle seat must be assembled on
bicycles with wheels with diameters of 26" and 28".
Specific instructions to assemble your seat on luggage
carrier of the bicycle (E-BD)
• The child bicycle seat must be assembled on a
carrier with a load capacity of 27kg, according to the
EN ISO 11243:2016 standard.
• The maximum weight applied to the carrier cannot
exceed 27kg, according to the EN ISO 11243:2016
standard
• For safety reasons this seat shall only be fitted
to luggage carriers in accordance with EN ISO
11243:2016 - 120 to 175 mm.
• The child bicycle seat must be assembled on
bicycles with wheels with diameters of 26" - 29".
4
Publicité
