Bobike Go mini Guide Rapide page 22

up - the word "TOP" must face up. Then make sure
that the front spacer of KIT A (E7.1) is correctly applied
to the body of the Mounting Block (E5) as shown.
Then offer up the assembly to the steering tube.
Next offer up the rear part (E7.2 + E7.3) so that the
block entirely surrounds the steering tube. Then
insert the 2 bolts (E4) and washers (E2) into the
mounting block (E).
Finally tighten the bolts using the key (E1). Make sure
that the mounting block (E) is tightly fixed and does
not move - correct tightening is extremely important
for the child's safety. We recommend tightening with
a 6 N.m torque. This step is extremely important for
child and cyclist safety.
Option B: Assembling the 1-1/8" kit on an MTB
bike steering tube.
Firstly, if necessary, remove the handlebar to obtain
the required space to assemble the block - remove
the original spacers of the steering tube. Then loosen
the bolts to remove the block (E7.1 + E7.2 + E7.3) that
is by default applied to the metallic block . No need
to remove the bolts.
Before inserting the Kit B (E6.1 + E6.2), make sure the
two parts are aligned as shown in the picture and
that the slots of both coincide.
Correctly place the front spacer of Kit B (E6.1) in the
body (E5) of the block. The slot must be at the bottom
to accommodate the bolts.
Make sure that the mounting-block body (E5) faces
up - the word "TOP" must face up. Then place the kit
on the steering tube as shown.
Position the mounting block (E5) as shown and slot in
the rear part of Kit B (E6.2). Make sure that the slot of
this part is at the bottom, aligned with the smaller part
and with the bolts already inserted into the block (E5).
How to safely place and secure the child on the seat
1. To safely place the child on the seat you must place
the bicycle on flat and solid ground for maximum
bicycle stability. Even if your bicycle offers robust
quick stands, you must always hold the bicycle, while
placing/ removing the child. You must carry your
child in your lap and safely place him on the seat. It´s
forbidden for the child to climb alone on the bicycle
or using the footrests to reach the seat. To place
the child in the seat, first fully extend the retention
system harness (B), by pressing the adjuster button
(B2.1) of the belt guide (B2), then pull it up - this
makes it easier to put the child in the seat.
Option A: Open the safety buckle (B1) by pressing
the safety buckle button. Seat the child, place the
shoulder straps and then close the safety buckle,
adjust the belt length using the strap adjusters, so
that your child is securely restrained.
Option B: Open the safety buckle (B1) by pressing
the safety buckle button, After releasing the buckle,
detach both sides by sliding one up and the other
down.Seat the child, place the shoulder straps and
then connect it by sliding the two parts of the buckle
together and close the safety buckle. Before fastening
the buckle, ensure that both sides are securely
connected.
How to Remove the Seat from the Bicycle
1. To remove your child seat remove the split ring (E3) and pull the child seat upwards and backwards to
release it from the mounting block (E).
Having positioned the block (E5) and its Kit (E6), it will
now be subject to final tightening. For the purpose
place the nuts (E6.3) in the corresponding rear
holes of the larger part of the Kit (E6.2). Please note
that these nuts are self-threading, so they must be
correctly fitted - the blue circle must face out.
Finally tighten the bolts using the key (E1). Make sure
that the mounting block (E) is tightly fixed and does
not move - correct tightening is extremely important
for the child's safety. We recommend tightening with
a 6 N.m torque. This step is extremely important for
child and cyclist safety.
4. Having concluded option A or option B, make
sure that the mounting block (E) is secure and
properly aligned with the handlebar and the wheel.
The mounting block (E) must be fitted as low as the
steering tube allows.
5. To assemble the child seat insert the two ends
of the steel rod (A1) of the child seat into the
corresponding holes (E5.1) of the mounting block
(E5). You will hear a slight click when the operation is
complete and you will see that the ends of the steed
rod (A1) appear beneath the mounting block (E).
6. Having fitted the child seat (A) to the mounting
block (E), conclude this stage by inserting the safety
ring (E3) in the hole at the end of the steel rod (A1).
This step is extremely important for the child's safety.
Make sure the child seat is upright.
7. Then sit on the bike and make sure that steering
and braking are not affected by any component of
the child seat. Also make sure that there is enough
space for the child between the seat and the
handlebars.
Before starting the journey, always check that the
child is secured and that the belt is snug but not so
tight that it hurts the child. According to the child
growth, current height, and weight, you can adjust
the height of the retention system harness (B) on all
the strap adjusters (B2), by pulling up or down the
straps until reaching the desired size.
2. To remove the footrest strap, lift it slightly to release
it from the footrest peg (D3) and slide it upwards to
disengage it from the footrest slot (D). Put the child's
foot in place. To fix the strap (D1), place its narrower
part of the footrest slot. Then pull the strap down to
fasten the appropriate hole to the footrest pin (D3).
On conclusion of these steps the footrest strap (D1) is
securely fastened to the peg (D3).
Next, adjust the height of the footrest to the child's
size. For the purpose, press the footrest button (D2)
and slide the footrest (D) up or down as appropriate.
Release the button to fix the footrest (D) in the
desired position. You will hear a slight click when the
operation is complete and the button (D2) will jump
to its normal position. Note - The chosen position
should cause the child's knee to be slightly straighter
rather than bent, a more comfortable position.
5