Bobike Go mini Guide Rapide page 21

A. Main seat
A1. Steel fixing rod ends
B. Retention system harness
B1. Safety buckle
B2. Height strap adjusters
B2.1. Adjustment button
C. Cushion
D. Footrest
D1. Footrest strap
D2. Footrest adjustment button
D3. Footrest strap fixing peg
E. Mounting block
E1. Key
E2. 2 x Washers
This product contains small parts like bolts, plastic bags, and small packaging hangers. Keep them out of
reach of children to avoid suffocation hazards.
• This child bicycle seat must not be mounted in
folding bicycles.
• This child bicycle seat must not be mounted to
bicycles fitted with rear shock absorbers.
• This child bicycle seat must not be mounted to
motorized vehicles such as mopeds and scooters.
• This child bicycle seat must not be mounted in
bicycles with triangular, square, or carbon fiber
frames.
• This child bicycle seat is only suitable for carrying
children with a maximum weight of 15 Kg, and
a maximum height of 93cm (and children with
recommended ages ranging from 9 months up to
3 years of age - with the weight and height as the
decisive variables).
• This child bicycle seat must be assembled on
bicycles with round frames with diameters ranging
from Ø22 to Ø32 mm.
• The child bicycle seat must be assembled on
bicycles with wheels with diameters of 26", 27,5", 28
and 29'' .
• The total weight of the cyclist and the child
transported must not exceed the maximum
Specific Instructions for Mounting the Seat in the Bicycle
1. Cut the security device so as to remove the
mounting block (E) from the steel rod (A1). Then, pull
the mounting block (E) down to release it.
2. Remove the 2 bolts (E4) and washers (E2) from the
mounting block (E). Use the key (E1).
3. Choose kit A or B. Consider whether your bike
Go® mini & One® mini
Table of Contents of Product
ATTENTION
Specific Instructions For Mounting
EN.
E3. Split ring
E4. 2 x M6 bolts
E5. Mounting block body
E5.1 Holes to insert the A1 rods
E6. Kit B - for MTB Bicycle - 1-1/8"
E6.1 Front spacer of KIT B
E6.2 Rear fastening part of KIT B
E6.3 2 x nuts for KIT B
E7. Kit A - Standard for Ø 22-32 mm handlebars
E7.1 Front spacer of KIT A
E7.2 Rear fastening part of KIT A
E7.3 Steel fastening plate for KIT A
F. Batch serial number
permitted load permitted for the bicycle. Information
on the maximum load can be found in the operating
instructions of the bicycle. You can also contact the
manufacturer for this question.
• The seat may only be mounted on a bicycle suitable
for the attachment of such additional loads. Please
consult your bicycle instructions manual.
• The position of the child bicycle seat must be
adjusted so that the bicycle rider does not touch the
child bicycle seat with the feet when in motion.
• It's very important to correctly adjust the seat and
its component parts for optimum comfort and safety
of the child. It's also important that the seat does not
slope forward so that the child does not tend to slide
out of it. It is also important that the backrest slope
backward slightly.
• Check if all parts of the bicycle function correctly
with the child bicycle seat mounted.
• Check the instructions of the bicycle, and If you
have any doubts about fitting the child bicycle seat
to your bicycle, please contact your bicycle supplier
for further information.
allows the Standard Kit (Option A) to be fitted or,
in the case of an MTB bike, whether the special kit
(Option B) is required.
Option A: Assembling with standard kit for Ø 22-
32mm steering tubes.
First, make sure that the body of the block (E5) faces
4