Publicité
Les langues disponibles
Les langues disponibles
Please provide the following information in the
event of any enquiries:
• Type of current for the motor
• Data of machine type plate
13.1 Replacing the blade (7) (Fig. 25)
m ATTENTION
Switch the mower off before starting with the work.
m NOTE
The blades (7) must be replaced after approx. 8
weeks. (2 sets of 3 blades each are included in the
delivery)
Use only original blades from the manufacturer. (Art.
no. 7913001601)
m ATTENTION
Put on protective gloves before replacing the blade
(7).
m ATTENTION
All blades (7) must always be changed at the same
time. The changing of individual blades (7) is not per-
mitted.
If the Phillips screws (8) are damaged or can no
longer be tightened, these must also be replaced.
New screws are included with the replacement
blades.
• To replace the blades (7), place the robotic lawn-
mower (1) on a workbench with the underside fac-
ing upwards. (We recommend a soft base to avoid
damage to the housing).
• Loosen the Phillips screw (8) with the help of a
Phillips screwdriver (not included in the scope of
delivery).
• Remove the old blade (7).
• Fit the new blade (7) and fasten it with a new screw
(8).
• Check that the blade (7) can move.
If this is not the case, loosen the screw (8) a little.
• Carry out this operation on all three blades (7).
13.2 Inserting/removing the rechargeable battery
(Fig. 26/27)
m ATTENTION
Switch the mower off before starting with the work.
• To install/remove the rechargeable battery, place
the robotic lawnmower (1) on a workbench with the
underside facing upwards. (We recommend a soft
base to avoid damage to the housing).
• Remove the battery cover screws and remove the
battery cover (Fig. 26/27).
• Remove the rechargeable battery retaining device.
34 | GB
• Pull the rechargeable battery out carefully.
m NOTE Do not pull on the cables.
• Loosen the locking and pull the connector off.
• Insert the rechargeable battery (if necessary a new
original rechargeable battery).
• Re-install the rechargeable battery in reverse order
(Fig. 26/27).
13.3 Software update (Fig. 28)
m NOTE The robot must be connected to the
WiFi in order to perform an automatic software
update via the app.
Connect your robot to your WiFi.
The software can be updated as soon as a new ver-
sion is available. (The latest software version can be
found on our homepage.)
The software can be installed via USB or the app.
The software for USB transmission can be download-
ed from our homepage www.scheppach.com.
13.3.1 Software update via USB
• Look for the latest software version on our home-
page.
• Download this to an empty FAT32 formatted disk.
• Remove the rechargeable battery covering as de-
scribed in 13.2.
• Insert the data carrier into the USB drive (Fig. 28).
• Switch the mower on by pressing the
("POWER ON/OFF" button).
• The update starts automatically.
• Wait until "OK" appears on the display and then re-
move the data carrier.
• Re-attach the rechargeable battery covering as de-
scribed in 13.2.
m NOTE
The operating manual supplied with your robotic
lawnmower (1) is based on the software version at
the time of production of the mower.
Some new or changed features and functions may
not be included in the operating manual.
You can find the latest version of the software in the
app or at www.scheppach.com.
Service information
With this product, it is necessary to note that the fol-
lowing parts are subject to natural or usage-related
wear, or that the following parts are required as con-
sumables.
Wearing parts*: Blade (7), screws (8), boundary wire
(11), wire pegs (12).
* may not be included in the scope of supply!
-Button
Publicité
