Mitsubishi Electric TRANE TPVFYP54AM141 Serie Manuel D'installation page 14

B
C
D
5 6
E
the latest RoHS directive.
F
RUBBER
PLUGS
G
H
9 10 11
I
Step.14c Remove the rubber plugs indicated in the image above.
Creo : 0_TOP_ASSY_L_21554B2.drw ( )
J
DETAIL A
1 2
2 PLASTIC TIES
PER SIDE
Step.14d Next, install the clear plastic tubes which are included
in the accessory bag. Ensure the plastic tubes drain into the pan.
Also, be sure the clear plastic tubes do not have any restriction.
Cutting of the plastic tube is required, please refer to the table for
length. Finally, secure the clear plastic tubes to the top drain pan
per Detail A. Then to the metal brackets supporting the coil to the
top drain pan with the provided plastic ties as shown.
14
DETAIL B
E
F
G
H
I
Creo : 0_TOP_ASSY_L_21554B2.drw ( )
J
7 8 9
1 2
Completed Step. 14b View
Horizontal Left Coil Assembly
12 13
3 4
RUBBER PLUGS
PLASTIC TIE
PLASTIC TUBE
Model
TPVFYP008, 12, 18, 24
TPVFYP030, 36
TPVFYP048, 54
10 11
3 4 5
*Tube length provided.
SIDE DRAIN PAN
14 15 16
Step.15 Reinstall the coil assembly along with bracket(s) that
secure(s) it. Failure to reinstall the brackets will result in capacity
loss and condensation formation inside the cabinet. The wiring
harness for the LEV needs to be rerouted back into the electrical
cabinet and plugged into the CN60 connector on the control board.
The wiring harness for the thermistor connector will also reroute
into the electrical section and plug into CN44. Refer to 9.3. Step 1
to 4 in reverse order to reassemble the panels. Ensure the proper
knockouts are removed for drainage and electrical connections.
proper knockouts are removed for drainage and electrical
connections.
Caution:
NOTE: For Horizontal installation an auxiliary drain pan must be
5 6 must be installed. 7
installed.
2 PLASTIC TUBES
ENSURE TUBES
DRAIN INTO
DRAIN PAN
9.D. Downflow Installations:
various changes to the air handler from its original configuration.
There are NO additional kits or parts required in order to convert the
Air Handler to the downflow configuration.
CORRECT INCORRECT
5/8"
(15mm)
DETAIL A
Tube Length
4.9 in. (125 mm)
6.9 in. (175 mm)
*8.9 in. (225 mm)
12 13
6 7 8 9
SIDE DRAIN PAN REATTACH
REATTACH
ON BOTTOM BRACKETS
ON BOTTOM BRACKETS
A
B
For Horizontal installation an auxiliary drain pan
8 9
C
PRIMARY DRAIN
3/4" FPT
AIRFLOW
D
Horizontal Left
Fan assembly rotation required
E
F
Downflow installation requires
G
MITSUBISHI ELECTRIC CORPORATION
PLASTIC TIE
PLASTIC TUBE
MITSUBISHI ELECT
DATE
DIM.mm
SCALE DRAWN
0.200 CHECKED
NTS
14 15 DESIGNED
10 11 12 13
MOTOR
MOTOR
ON BOTTOM
ON BOTTOM
10 11
C
Auxiliary
drain pan
Step.2
A. Remove the Cont
B. Unplug the LEV (C
board and route the
rubber grommet.
C. Remove the brack
already done.
D. Slide the coil asse
ITEM
COMMER
WOR
CASTI
PRESS WO
GAS CUT
SHEAR
MACHIN
12