Residual Heat Indicator; Twistpad With Twist Knob; Removing The Twist Knob; Storing The Twist Knob - NEFF T13T42 Série Mode D'emploi

Residual heat indicator

The hob has a two-stage residual heat indicator for each
hotplate.

Twistpad with twist knob

The twistpad is the area in which you can select the hotplates
and set heat settings using the twist knob. The twist knob
automatically centres itself in the twistpad.
The twist knob is magnetic and is placed on the twistpad.
Tapping the twist knob where there is a marking activates the
relevant hotplate. Turning the twist knob sets the heat setting.

Removing the twist knob

You can remove the twist knob. This makes cleaning easier.
You can also remove the twist knob while the hotplate is in
operation. The wipe protection function is activated and
switches the hotplate off after 35 seconds.
:
Risk of fire!
If you place a metal object on the twistpad, the hob may
continue to heat up. For this reason, always switch off the hob
using the main switch.

Setting the hob

This section informs you how to set the hotplates. The table
shows heat settings and cooking times for various meals.

Switching the hob on and off

The main switch is used to switch the hob on and off.
To switch on: touch the
#
indicator above the main switch lights up. The hob is ready for
use.
To switch off: touch the
#
main switch goes out. All hotplates are switched off. The
residual heat indicator remains on until the hotplates have
cooled down sufficiently.
Notes
The hob switches off automatically if all hotplates have been
■
switched off for more than 15 seconds.
The settings remain stored for 4 seconds after the hob has
■
been switched off. If you switch it on again during this time,
the hob will operate using the previously stored settings.

Setting a hotplate

Use the twist knob to set the desired cooking time.
Heat setting 1 = lowest setting
30
symbol. A signal sounds. The
symbol until the display above the
If appears in the display the hob is still hot. It may be used,
•
for example, to keep a small meal warm or to melt cooking
chocolate. As the hotplate cools down further, the display
changes to . The display remains lit until the hotplate has
œ
cooled sufficiently.

Storing the twist knob

The twist knob contains a strong magnet. Keep the twist knob
away from magnetic data carriers, such as video cassettes,
diskettes, credit cards or cards with magnetic strips. The data
these contain could otherwise be wiped. They can also cause
interference in television sets and monitors.
:
Hazard due to magnetism!
For wearers of electronic implants, e.g. pacemakers or insulin
pumps. Implants could be affected by magnetic fields. You
must therefore never carry the twist knob in a pocket in your
clothing. They must be kept at least 10 cm from pacemakers.
Note: The twist knob is magnetic. Metal particles which stick to
the underside can scratch the ceramic hob top. Always wipe
the twist knob thoroughly.

Operation without the twist knob

If you have misplaced the twist knob, you can operate the hob
without it:
Switch on the hob using the main switch.
1.
Within the next 5 seconds, simultaneously touch the L and
2.
symbols. A signal sounds.
Touch the 3 symbol repeatedly until the indicator for the
3.
desired hotplate lights up.
Set the desired heat setting using the L (-) and
4.
The hotplate is switched on.
Note: You can place the twist knob back on the twistpad at any
time.
Heat setting 9 = highest setting
There is an intermediate setting between each heat setting. This
is identified by a dot.
Set the heat setting
The hob must be switched on.
Select the hotplate. To do this, tap the twist knob in the
1.
appropriate area for the desired hotplate.
Within the next 5 seconds, turn the twist knob until the
2.
desired heat setting indicator appears in the heat setting
display.
The hotplate is switched on.
3
ó (+) symbol.