Residual Heat Indicator; Twistpad With Twist Knob; Removing The Twist Knob; Storing The Twist Knob - NEFF T1.T90 Série Mode D'emploi

â
Hotplates with bridge heating element
Two individual hotplates can be interconnected with a bridge
heating element to create one large extended cooking zone
Under normal operation, these hotplates both work as normal
single-circuit and dual-circuit hotplates.
To activate the bridge heating element: the single-circuit
hotplate must be switched off.
Switch on the dual-circuit hotplate.
1.
Touch the symbol. The outer filament circuit on the dual-
ë
2.
circuit hotplate is activated. The indicator light comes on.
Touch the ë symbol again. The extended cooking zone is
3.
activated. The indicator light comes on.

Twistpad with twist knob

The twistpad is the area in which you can select the hotplates
and set heat settings using the twist knob. The twist knob
automatically centres itself in the twistpad.
The twist knob is magnetic and is placed on the twistpad.
Tapping the twist knob where there is a marking activates the
relevant hotplate. Turning the twist knob sets the heat setting.

Removing the twist knob

You can remove the touch knob. This makes cleaning easier.
You can also remove the twist knob while the hotplate is in
operation. All the hotplates switch off after 3 seconds.
ã=
Risk of fire!
If you place a metal object on the twistpad within 3 seconds,
the hob may continue to heat up. For this reason, always switch
off the hob using the main switch.

Storing the twist knob

The twist knob contains a strong magnet. Keep the twist knob
away from magnetic data carriers, such as video cassettes,
diskettes, credit cards or cards with magnetic strips. The data

Setting the hob

This section informs you how to set the hotplates. The table
shows heat settings and cooking times for various meals.

Switching the hob on and off

The main switch is used to switch the hob on and off.
To switch on: touch the
#
indicator above the main switch lights up. The hob is ready for
use.
To switch off: touch the
#
main switch goes out. All hotplates are switched off. The
symbol. A signal sounds. The
symbol until the display above the
To deactivate the extended cooking zone: touch the
again. The indicator light goes out. The extended cooking zone
is deactivated.
You can also change the heat setting using the control panels
for the two hotplates.

Residual heat indicator

The hob has a two-stage residual heat indicator for each
hotplate.
If • appears in the display the hob is still hot. It may be used,
for example, to keep a small meal warm or to melt cooking
chocolate. As the hotplate cools down further, the display
changes to œ . The display remains lit until the hotplate has
cooled sufficiently.
these contain could otherwise be wiped. They can also cause
interference in television sets and monitors.
ã=
Hazard due to magnetism!
For wearers of electronic implants, e.g. pacemakers or insulin
pumps. Implants could be affected by magnetic fields. You
must therefore never carry the twist knob in a pocket in your
clothing. They must be kept at least 10 cm from pacemakers.
Note: The twist knob is magnetic. Metal particles which stick to
the underside can scratch the ceramic hob top. Always wipe
the twist knob thoroughly.

Operation without the twist knob

If you have misplaced the twist knob, you can operate the hob
without it:
Switch on the hob using the main switch.
1.
Within the next 5 seconds, simultaneously touch the L and
2.
symbols. A signal sounds.
Touch the " symbol repeatedly until the display for the
3.
desired hotplate lights up.
Touch the L symbol repeatedly until the desired heat setting
4.
appears on the heat setting display.
The hotplate is switched on.
Notes
The timer function can be activated in the usual way. The
■
cooking time must be set with the L symbol.
The automatic zone control functions as usual.
■
You can place the twist knob back on the twistpad at any
■
time.
residual heat indicator remains on until the hotplates have
cooled down sufficiently.
Notes
The hob switches off automatically if all hotplates have been
■
switched off for more than 15 seconds.
The settings remain stored for 4 seconds after the hob has
■
been switched off. If you switch it on again during this time,
the hob will operate using the previously stored settings.
ë symbol
3
25