Télécharger Imprimer la page

Stihl HTA 150.0 Notice D'emploi page 57

Publicité

Les langues disponibles
  • FR

Les langues disponibles

20 Specifications
– Data connection: Bluetooth
mobile appliance must be compatible with
®
Bluetooth
Low Energy 5.0 and support
Generic Access Profile (GAP).
– Frequency band: ISM band 2.4 GHz
– Maximum RF power transmitted: 1 mW
– Signal range: approx. 10 m. The signal
strength depends on the ambient conditions
and the mobile terminal. Signal range can
vary greatly depending on local conditions,
including the receiver. The range may be
perceptibly reduced inside enclosed rooms
and through metal barriers (such as walls,
shelves or cases).
– Mobile appliance operating system require‐
ments: Android or iOS (current version or
higher)
20.6
Temperature limits
WARNING
■ The battery is not protected against all ambi‐
ent conditions. If the battery is exposed to cer‐
tain environmental conditions, it may catch fire
or explode. This may result in serious injury to
people and damage to property.
► Do not charge the battery below -20°C or
above 50°C.
► Do not use the pole pruner or battery below
-20°C or above 50°C.
► Do not use the pole pruner or battery below
-20°C or above +70°C.
20.7
Recommended temperature
ranges
For optimum performance of the pole pruner and
battery, observe the following temperature
ranges:
– Charging: 5°C to 40°C
– Use: - 10 °C to + 40 °C
– Storage: - 20 °C to + 50 °C
If the battery is charged, used or stored outside
the recommended temperature ranges, perform‐
ance may be reduced.
If the battery is wet or moist, allow the battery to
dry for at least 48 h between 15°C and 50°C and
with less than 70% humidity. Higher humidity
may extend the drying time.
20.8
Sound values and vibration val‐
ues HTA 150.0
The K value for the sound pressure level is
2 dB(A). The K value for the sound power level is
0458-038-9602-A
®
5.1. The
2 dB(A). The K-value for vibration levels is 2
m/s².
STIHL recommends wearing hearing protection.
– Sound pressure level L
ance with IEC 62841-4-10 for 3/8" P: 94 dB(A)
– Sound pressure level L
ance with IEC 62841-4-10 for 1/4" P: 89 dB(A)
– Sound power level L
ance with IEC 62841-4-10 for 3/8" P:
100 dB(A)
– Sound power level L
ance with IEC 62841-4-10 for 1/4" P: 96 dB(A)
Handle hose:
– Vibration value a
hv
with IEC 62841-4-10
– Control handle: 4.8 m/s².
– Handle hose: 3.6 m/s²
Loop handle:
– Vibration value a
hv
with IEC 62841-4-10
– Control handle: 5.6 m/s².
– Loop handle: 4.0 m/s²
The vibration levels indicated were measured
according to a standardized test method and can
be used as a basis for comparing electric power
tools. The vibration levels actually occurring may
vary from the values indicated, depending on the
type of application. The vibration levels indicated
can be used for an initial estimate of the vibration
load. The actual vibration load has to be estima‐
ted. The times can be taken into account in the
estimate when the electric power tool is switched
off and also when it is switched on but running
without any load.
For information on compliance with the Physical
Agents (Vibration) Directive 2002/44/EC, see
www.stihl.com/vib.
20.9
Sound values and vibration val‐
ues HTA 160.0
The K value for the sound pressure level is
2 dB(A). The K value for the sound power level is
2 dB(A). The K-value for vibration levels is 2
m/s².
STIHL recommends wearing hearing protection.
– Sound pressure level L
ance with IEC 62841-4-10 for 3/8" P: 89 dB(A)
– Sound pressure level L
ance with IEC 62841-4-10 for 1/4" P: 85 dB(A)
English
measured in accord‐
pA
measured in accord‐
pA
measured in accord‐
wA
measured in accord‐
wA
measured in accordance
measured in accordance
measured in accord‐
pA
measured in accord‐
pA
57

Publicité

loading

Ce manuel est également adapté pour:

Hta 160.0