Simons Voss Technologies BS21.990604 Guide Abrégé page 32

10. Removing the fitting
8. Place a cover with the notch facing downwards on the escutcheon
base.
23
9. Place the cover on the fitting.
24
10. Fit the outside handle into position on the fitting.
25
11. Determine the required direction of rotation for your inner handle.
12. Insert the spring element appropriately.
13. Place the underlay in the inner handle unit.
26
27
14. For 8.5 mm and 10 mm spindle: slide the adapter sleeve into the centre
of the spindle. Use a punch and hammer to make an indent in the ad-
apter sleeve to prevent it from slipping.
28
29
15. Measure the total length of the spindle.
30
16. Locate the inside of the spindle (four-edge end up to the centre of the
first groove = 26 mm).
17. Use the table to determine the position of the O-ring.
31
Door thickness
Area
(mm)
S 40 - 42
S 40 - 42
S 43 - 47
S 43 - 47
S 48 - 52
S 48 - 52
S 53 - 57
S 58 - 61
M 60 - 62
M 60 - 62
M 63 - 67
M 63 - 67
M 68 - 72
M 68 - 72
M 73 - 77
M 78 - 81
L 80 - 82
L 80 - 82
L 83 - 87
L 83 - 87
L 88 - 92
L 88 - 92
L 93 - 97
L 98 - 101
XL 100 - 184
18. Slide the O-ring onto the calculated groove.
32
32 / 60
Spindle length
Ring position
(mm)
94 3
104 5
94 2
104 4
94 1
104 3
104 2
104 1
114 3
124 5
114 2
124 4
114 1
124 3
124 2
124 1
134 3
144 5
134 2
144 4
134 1
144 3
144 2
144 1
O-ring is 30–35 mm from the cut
end of the spindle.
Digital SmartHandle AX Metal frame
19. Insert the spindle into the door with the ring-free side as far as it will go.
33
20. For FH: insert the dummy cylinder.
NOTE
Feed the blank cylinder into the hole using a screwdriver
It is difficult to position the blank cylinder correctly, especially in thick doors.
1. Insert a screwdriver into the hole in the blank cylinder.
2. Position the blank cylinder using the screwdriver.
34
35
21. For FH: screw the dummy cylinder firmly into place (PH2, torque 1.1 Nm).
36
22. Screw the inner handle unit onto the spindle (PH2, torque 1.1 Nm).
37
23. Screw the escutcheon base firmly into place on the inside (PH2, torque
1.1 Nm).
38
24. Fasten the grub screws firmly onto both handles (TX15, torque 5.0 Nm).
39
25. Place the inner handle cover with the notch facing downwards onto the
inner handle escutcheon.
40
26. Place a cover with the notch facing downwards on the escutcheon
base.
41
Fitting is now installed.
9
10. Removing the fitting
ü 1.5 mm hexagonal wrench available.
1. Remove the fitting in the reverse order to installation.
2. Insert a 1.5 mm hex key into the hole in the spindle mount in the fitting.
42
3. Bend the hex key to the side where the hole is located while pulling on
the outside handle.
43
9 Fitting is now removed.
11. Replacing the batteries
NOTE
Malfunctions due to poor contact or different discharge
Contact surfaces that are too small/contaminated or different discharged
batteries can lead to malfunctions.
1. Only use batteries that are approved by SimonsVoss.
2. Do not touch the contacts of the new batteries with your hands.
3. Use clean and grease-free gloves.
4. Always replace all batteries at the same time.
Special tool at hand.
ü
Gloves at hand.
ü
1. Insert the special tool into the fitting's cover inlay.
44
2. Remove the cover with the tool.
45
EN