Publicité
Les langues disponibles
Les langues disponibles
If using the Cooking Chef Connect without heat, it is
not necessary to fit the heat shield unless using the
splashguard. Refer to 'To Fit and Use Your Splashguard
Assembly' section.
4
Fit the bowl to the base.
5
Place the required tool in the bowl tool socket or stir tool
socket if using the stir tool, locating the pin in the groove
and then turn to lock into position.
To remove a tool, reverse step 5 above. (Always use oven
gloves to remove tools after cooking).
6
To lower the mixer head, raise it slightly, then turn the head
lift lever clockwise.
Lower into the locked position.
Stir Tool – when using the stir tool the stir assist clip can also
be used to assist the mixing action, see 'to fit and remove
your stir assist clip'. The stir tool can also be used with the
whisk. Do not use the stir tool with the dough tool.
To Use Your Cooking Chef Connect - Manual
Operation
1
Add the relevant ingredients to be cooked/mixed.
2
Set the required time, speed and temperature.
Note: To use the machine as a mixer without heat, select
'Off' when setting the temperature.
Turn the control dial anti-clockwise to use stir intervals and
pulse.
Turn the control dial clockwise to use continuous speeds.
3
Press the control dial to start.
4
To stop the unit at any time, press the control dial. If in
cooking mode, take care as the unit will be hot.
If the bowl temperature exceeds 60°C, for safety reasons
the speed is automatically limited even if a higher speed
has been selected. The speed will not automatically
increase when the temperature drops below 60°C. The
speed must be turned to the Off position first and the
desired speed reselected.
High speed, high temperature mode (HSHT)
To mix at high speed at temperatures of 60°C and above
Select time (if applicable), speed and temperature of
60°C or above.
A warning will pop up on the display screen advising that
you are entering HSHT mode
Once the warning has been read and undestood, press
yes to confirm that you are happy to enter HSHT mode.
Press the control dial to start.
This function MUST ONLY be used with the whisk and/
or stir tool. You should not exceed the maximum cooking
capacity of 3 litres and you must ensure the splashguard is
fitted. The machine must not be left unattended.
5
Once a programme has finished, the unit will beep 3 times.
Note: If no time has been set, the heating and stirring
processes will automatically end once the timer has
reached 8 hours.
6
To stop the heating process, change the temperature to
'OFF'. To stop the unit at any time press the control dial.
Important – If at any time the mixer head is raised during
an operation, the heating process will pause and the bowl
tool will stop and will not restart when the mixer head is
lowered. To restart the mixer, lower the mixer head and
press the control dial.
Using Preset Programmes
P
Refer to Illustrations
1
Select the Preset Menu.
2
Choose the preset you wish to use.
3
Follow the instructions on the display screen.
4
To stop the unit at any time, press the control dial. Take
care as the bowl and tools will be hot.
After Cooking
Be careful when handling or touching any part
of the appliance when being used in the cooking
mode or after cooking, IN PARTICULAR THE
BOWL AND TOOLS as they will remain HOT long
after the appliance has been switched off.
Use the two side handles to remove and carry the
bowl. Use oven gloves when handling the hot bowl
and hot tools.
The underside of the bowl will remain hot long after
the heating has stopped. Use caution when handling
and use the work surface protection mat provided
to protect heat sensitive surfaces.
Hints and Tips
Some recipes, in particular those with a high water
content, will not be able to reach a cooking temperature
above 100°C (as this is the boiling point of water).
When adding ingredients to the bowl during cooking,
turn the speed down and add the ingredients slowly and
evenly.
To heat sauces quickly use a continuous stir setting.
If using the splashguard during cooking, always
remove it before lifting the mixer head. Be aware of
condensation formed on the splashguard and heat
shield.
When lifting the mixer head lift it slowly to allow any
liquid on the underside of the heat shield to flow back
into the bowl.
Four stir delay functions are available which enable
you to select the appropriate amount of stirring for
individual recipes. Some recipes will require constant
stirring to stop ingredients from sticking to the
bottom of the bowl, whereas others will benefit from
intermittent stirring to maintain the texture of the food.
To Use The Weighing Function
Refer to Illustrations
S
1
Select the weighing function
2
Fit the bowl.
3
Zero the scale.
4
Weigh the ingredients.
5
To change between units tap the unit button on the
weighing screen.
Note: Always place the appliance on a dry flat, stable surface
prior to weighing. Do not apply pressure to the mixer or bowl
whilst weighing as this will affect the accuracy of the scales.
The weighing function can be used with the mixer head in
either the down or up position.
5
R
–
on the touch screen.
Publicité
