Bracelet Link Removal - Timex Metropolitan Mode D'emploi

TACHYMETER RING
The tachymeter feature can be used to measure speed in miles per hour
(MPH), nautical miles per hour (knots) or kilometers per hour (KPH) using the
sweep second hand and the scale on the wall above the watch face. You
need to know the actual distance you are covering in miles or km.
Start the chronograph with the second hand at zero (the twelve o'clock
position). Within the first minute, the second hand will point to the rate for a
one-mile (or one kilometer) course: if it takes 45 seconds, the hand will point
to 80 at that position – 80 MPH or 80 KPH.
If within the first minute, a distance greater than one mile or kilometer is cov-
ered, multiply the tachymeter number by the distance to get the actual rate:
if you went 1.2 miles in 45 seconds, multiply the 80 by 1.2 – 96 MPH.
COMPASS RING
If your watch is equipped with a movable ring around the dial marked
at the letters "N", "E", "W", "S" (for the four compass directions) or com-
pass degrees, you can use this feature to find an approximate compass
directional reading.
1) Lay the watch on a flat surface, or hold it so that the face is parallel to the
ground.
2) Locate the sun and point the hour hand at the sun.
3) In the A.M., rotate the ring until the "S" (south) marker is halfway between
the hour hand and 12:00 (after the hour hand or within the shortest dis-
tance between the hour hand and 12:00).
4) In the P.M., rotate the ring until "S" is before the hour hand and halfway
between the hour hand and 12:00.
12 1
11
10
9
8
7
6
HOW TO ADJUST BRACELET
(Variations of the following bracelet sections apply to all watch models).
SLIDING CLASP BRACELET
1. Open locking plate.
2. Move clasp to desired bracelet length.
3. Exert pressure while holding locking plate and slide clasp back and forth
until it engages in grooves on underside of bracelet.
4. Press locking plate down until it snaps closed. Clasp can be damaged if
excessive force is used.
2
3
4
5
N
Register your product at www.timex.com
FOLDOVER CLASP BRACELET
1. Find spring bar that connects bracelet to clasp.
2. Using a pointed tool, push in spring bar and gently twist bracelet to
disengage.
3. Determine wrist size, then insert spring bar in correct bottom hole.
4. Push down on spring bar, align with top hole and release to lock in place.
FIG. 1

BRACELET LINK REMOVAL

REMOVING LINKS:
1. Place bracelet upright and insert pointed tool in opening of link.
2. Push pin forcefully in direction of arrow until link is detached (pins are
designed to be difficult to remove).
3. Repeat until desired number of links are removed.
RE-ASSEMBLY:
1. Rejoin bracelet parts.
2. Push pin back into link in opposite direction of arrow.
3. Press pin down securely into bracelet until it is flush.
BATTERY
Timex strongly recommends that a retailer or jeweler replace battery. Battery
type is on watch back. If present, push/short internal reset switch after replac-
ing battery. Battery life estimates are based on certain assumptions regarding
usage; battery life may vary depending on actual usage.
DO NOT DISPOSE OF BATTERY IN FIRE. DO NOT RECHARGE. KEEP
LOOSE BATTERIES AWAY FROM CHILDREN.
TIMEX INTERNATIONAL WARRANTY
http://www.timex.com/productWarranty.html
©2017 Timex Group USA, Inc. TIMEX, INDIGLO and QUICKDATE are
registered trademarks of Timex Group B.V. and its subsidiaries.
3
ENGLISH 990-095926-02
REVISED 2.5.2018
FIG. 2 FIG. 3