Flex L 24-6 230 Notice D'instruction D'origine page 13

L 15-10 150 / L 21-6 230 / L 21-8 180 / L 24-6 230 / L 2100
CAUTION!
The indicated measurements refer to new power tools.
Daily use causes the noise and vibration values to change.
NOTE
The vibration emission level given in this information sheet has
been measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with another.
It may be used for a preliminary assessment of exposure. The
declared vibration emission level represents the main applications
of the tool. However if the tool is used for different applications, with
different accessories or poorly maintained, the vibration emission
may differ. This may significantly increase the exposure level over
the total working period.
However if the tool is used for different applications, with different
accessories or poorly maintained, the vibration emission may
differ. This may significantly decrease the exposure level over the
total working period.
Identify additional safety measures to protect the operator from the
effects of vibration such as: maintain the tool and the accessories,
keep the hands warm, organisation of work patterns.
CAUTION!
Wear ear protection at a sound pressure above 85 dB(A).
Overview (Figure A)
Different electric power tools are described in these instruc-
tions. The illustrated electric power tool may differ in detail from
the one which you purchased.
1 Switch
Switches the power tool on and off.
2 Starting lockout/Locking button
Prevents the power tool from starting up unintentionally
and locks the switch during continuous operation.
3 Quick-clamping lever
4 Spindle
5 Threaded flange
a Clamping nut
b Clamping flange
6 Guard
7 Gear head
With air outlet and direction-of-rotation arrow.
8 Auxiliary handle
Side handle can be fitted on the left, the top or the right.
9 Spindle lock
Secures the spindle when the tool is changed.
10 Switch handle
11 4.0 m power cord with plug
12 Stop key
13 Rating plate (not shown)
Operating instructions
WARNING!
Before carrying out any work on the angle grinder, always pull
out the mains plug.
Before switching on the angle grinder
Unpack the angle grinder and check that there are no missing
or damaged parts.
Figure B:
Connect the guard to the clamping flange with the clamping

ring by inserting the cam on the clamping ring into the
groove on the flange (1.).
Figure C:
Rotate guard hood into the required position (2.) and tight-

en clamping lever (3.)
Attaching the auxiliary handle.

Switch on and off
Brief operation without engaged switch rocker
(Figure D)
Press and hold down the starting lockout (1.).

Press the switch (2.).

To switch off, release the switch.

Continuous operation with engaged switch rocker
Figure E:
Press and hold down the starting lockout (1.).

Press and hold down the switch (2.).

Press the locking button (3.).

Figure F:
To switch off, briefly press and release the switch.

Adjusting the quick-release guard (Figure G)
WARNING!
Before carrying out any work on the angle grinder, always pull
out the mains plug.
When using the angle grinder for roughing or cutting, never
work without the guard.
A special cutting guard must be used for cut-off grinding.
CAUTION!
Risk of injury! Wear protective gloves!
Loosen the clamping lever (1.).

Adjust the guard (2.).

Retighten the clamping lever (3.).

Attaching or changing the grinding tool
(Figure H)
WARNING!
Before carrying out any work on the angle grinder, always pull
out the mains plug.
Press and hold down the spindle lock (1.).

Using the face spanner, loosen the clamping nut on the

spindle in an anti-clockwise direction and remove (2.).
Insert the grinding wheel in the correct position.

Figure I:
Screw the clamping nut onto the spindle.

– Grinding wheel ≤6 mm thick:
Clamping nut collar face up, towards shaft end.
– Grinding wheel > 6 mm thick:
Clamping nut collar face down, towards gearbox.
Press and hold down the spindle lock.

Tighten the clamping nut with the face spanner.

Insert the mains plug into the socket.

Switch on the angle grinder (without locking into position)

and leave the angle grinder running for
approx. 30 seconds. Check for imbalances and vibrations!
Switch off the angle grinder.

Operating instructions
NOTE
When the angle grinder is switched off, the grinding tool
continues running briefly.
Rough-grinding
WARNING!
Never use cutting-off wheels for rough-grinding.
–
Angle of wheel 20–40° for best cutting performance.
13