General Warnings - Flotec FPT20075 Notice D'utilisation

Safety
• Filter tank lid and strainer cover must be properly
secured to prevent violent separation.
• Stand clear of all circulation system equipment when
turning on or starting up pump.
• Before servicing pool and spa equipment, make note
of the filter pressure. Be sure that all controls are set
to ensure the system cannot inadvertently start during
service. Turn off all power to the pump.
• Place filter manual air relief valve in the open
position and wait for all pressure in the system to
be relieved.
• Before starting the system, fully open the manual air
relief valve and place all system valves in the "open"
position to allow water to flow freely from the pool
and spa back to the pool or spa. Stand clear of all
pool and spa equipment and start the pump.
• Do not close filter manual air relief valve until all
pressure has been discharged from the valve and
a steady stream of water appears. Observe filter
pressure gauge and be sure it is not higher than the
pre-service condition.
Warnings and safety instructions for these pumps are
available at: http://www .pentairpool .com/pool-owner/
safety-warnings/ or call (800) 831-7133 for additional
free copies of these instructions.

General Warnings

• All work must be performed by a qualified pool
professional, and must conform to all national, state,
and local codes.
• Install to provide drainage of compartment for
electrical components.
• These instructions contain information for a variety
of pump models and therefore some instructions
may not apply to a specific model. All models are
intended for use in swimming pool applications.
The pump will function correctly only if it is
properly sized to the specific application and
properly installed.
Risk of harm . Pumps improperly sized or
installed or used in applications other than for which the
pump was intended can result in severe personal injury
or death. These risks may include but not be limited
to electric shock, fire, flooding, suction entrapment or
severe injury or property damage caused by a structural
failure of the pump or other system component.
Electrical controls such as on/off switches,
timers, and control systems, etc. should be properly
installed to allow the operation (start-up, shut-down,
or servicing) of any pump or filter without requiring
the user to place any portion of his/her body over or
For parts or assistance, call Flotec Customer Service at 1-800-365-6832.
near the pump strainer lid or filter lid. Such installation
should allow the user to stand clear of the filter and
pump during system start-up, shut down or servicing of
the system.
Hazardous voltage . Capacitor voltage
may be hazardous. To discharge motor capacitor, hold
insulated handle screwdriver BY THE HANDLE and
short capacitor terminals together. Do not touch metal
screwdriver blade or capacitor terminals. If in doubt,
consult a qualified electrician.
• The pump is not submersible.
• The pump is designed for use with chlorinated
pools only. For use with other applications, contact
customer service.
• The pump is capable of high flow rates; use
caution when installing and programming to
limit pumps performance potential with old or
questionable equipment.
• Code requirements for the electrical connection
differ from state to state. Install equipment in
accordance with the National Electrical Code and all
applicable local codes and ordinances.
• Before servicing the pump, switch OFF the pump by
disconnecting the main circuit to the pump.
• This appliance is not intended for use by persons
(including children) of reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning the use of the appliance by
a person responsible for their safety.
Complies with Energy Efficiency Requirements: This
pump complies with energy efficiency standards when
installed with a compatible controller programmed
to default to low-speed after any high-speed override.
When installed and programmed, this pump and
compatible controller meet the requirements of
California Title 20, 24, and ANSI/APSP/ICC 15 -2011,
Standard for Residential Swimming Pool and Spa
Energy Efficiency.
Flotec® and Pentair Water Pool and Spa® are registered
trademarks of Pentair, Inc. and/or its affiliated companies
in the United States and/or other countries. Unless
noted, names and brands of others that may be used in
this document are not used to indicate an affiliation or
endorsement between the proprietors of these names and
brands and Pentair, Inc. Those names and brands may be
the trademarks or registered trademarks of those parties
or others.
4