Güde 480/10/200 ST Traduction Du Mode D'emploi D'origine page 29

for each type of application (inflation, airpowered
tools, painting, washing with water-based deter-
gents only, clinching, etc.).
When using compressed air, you must know and
comply with the safety precautions to be adopted
for each type of application (inflation, airpowered
tools, painting, washing with water-based deter-
gents only, clinching, etc.).
Caution! Never switch the compressor on or off using
the plug. Pressure switch to be pressed at all times.
Do not leave the compressor on over night as it could
become a source of danger.
At the end of your working day, switch the appliance
off, release the air jet and unplug the compressor.
Warning: if the water that condenses is not drained,
it may corrode the receiver, reducing its capacity and
impairing safety.
As it is a contaminating product, condensate must be
DISPOSED of in accordance with laws on protection
of the environment and current legislation.
Never leave the appliance exposed to adverse wea-
ther conditions (rain, sun, fog, snow).
If this compressor is used outdoors, always remem-
ber to stow it after use in a covered or closed place.
Never use the compressor outdoors in rain or bad
weather.
Do not place flammable or nylon/fabric objects close
to and/or on the compressor.
Do not cover the air inlets on the compressor.
The compressor must not be fitted in a vehicle for
industrial purposes without an inspection by an
expert!
If the compressor is used for industrial purposes, it
must be checked by an expert before putting into
operation for the first time. Such check must be orde-
red by the operator (under BetrSichV Section 17 No.
25 – operation safety regulation)
Caution! When fitted in automatic equipment, it is
necessary to install appropriate alarm or warning
devices in case of power outage or malfunction or
compressor (e.g. feed line, etc.) failure.
Keep unused machinery and tools safely in a dry
place out of the reach of children.
Operation of compressed air tools
To guarantee perfect and reliable operation of
the rotary and percussive pneumatic tools such as
impact wrenches, staplers or nailers, etc., the com-
pressed air must be supplied filtered - with oil via the
lubricator or maintenance unit
A filtered water separator should be used for var-
nishing in any case.
To select a suitable pneumatic tool, the tool air
consumption and the compressor effective amount
delivered must necessarily be considered.
(Pneumatic tools and accessory equipment can be
found at www.guede.com)
Operation at lower temperatures
At lower temperatures, below 5°C, problems may
be experienced when starting. They are manifested
by growling of the electric motor. In such a case, the
appliance must be immediately switched off and oil
(5W30) changed in warmer conditions.
Requirements for operating staff
The operating staff must carefully read the Opera-
ting Instructions before using the appliance.
Qualification: Apart from the detailed instructions
by a professional, no special qualification is necessa-
ry for appliance using.
Minimum age: Persons over 16 years of age can
only work on the appliance. An exception includes
youngsters trained in order to reach knowledge
under supervision of the trainer during occupational
education.
Training: Using the appliance only requires corre-
sponding training by a professional or the Operating
Instructions. No special training is necessary.
Emergency procedure
Conduct a first-aid procedure adequate to the injury
and summon qualified medical attendance as quickly
as possible. Protect the injured person from further
harm and calm them down. For the sake of eventual
accident, in accordance with DIN 13164, a workplace
has to be fitted with a first-aid kit. It is essential to
replace any used material in the first-aid kit immedia-
tely after it has been used.
If you seek help, state the following pieces of infor-
mation:
1. Accident site
2. Accident type
3. Number of injured persons
4. Injury type(s)
Disposal
The disposal instructions are based on the icons
placed on the appliance or on the package. Descrip-
tion of the respective meanings can be found in the
section „Marking".
ENGLISH
25