Barbecook SIESTA 310 BLACK EDITION Mode D'emploi page 10

8.3 Burning in the appliance
By burning in the appliance before the first use, you remove
remaining manufacturing greases from the appliance. Proceed
as follows:
1. Light the main burners and set their control knobs to HIGH.
See "9.2 Lighting the main burners".
2. Close the lid and let the appliance burn for 15 minutes. Do
not put any food on the grill yet.
3. After 15 minutes, open the lid and let the appliance burn for
another 5 minutes (control knobs still set to HIGH).
4. After 5 minutes, the appliance is ready for use. You can now
put food on the grill.
9 LIGHTING THE BURNERS
To light the burners with the electrical igniter, you have
to install an AA battery in the igniter. That battery is not
supplied with the appliance. You can find the battery case
of the igniter at the inside of the front panel of the right
side table.
9.1 Safety instructions
• Before you light the appliance, execute all checks listed in
"8 Getting the appliance ready for use".
• Make sure the lid is always open when you light a burner .
• Never bend directly over a burner when lighting it.
9.2 Lighting the main burners
9.2.1 U
sing the igniter
1. Open the lid and set the control knobs of the main burners
to OFF.
2. If no other burner is lit yet, open the gas supply and wait ten
seconds. This allows the gas to stabilize.
3. Push in the control knob of one burner, set it to HIGH and
hold it for a moment. The build-in igniter will cause sparks,
which will light the burner.
Always light one main burner to start with. Never light all
main burners at the same time.
4. If the burner does not light after three attempts, set its
control knob to OFF, close the gas supply and wait 5
minutes. This allows any accumulated gas to escape.
5. Retry lighting the burner. If it still does not light, try lighting it
with a match or refer to "14 Troubleshooting" to determine
the cause of the problem.
9.2.2 U
sing a match
1. Place a match in the match holder.
2. Open the lid and set the control knobs of the main burners
to OFF.
3. lf no other burner is lit yet, open the gas supply and wait ten
seconds. This allows the gas to stabilize.
4. Light the match and hold it about 13 mm from the burner.
10
All manuals and user guides at all-guides.com
5.
6.
7.
8.
9.3 Lighting the side burner
9.3.1
1.
2.
3.
4.
6.
9.3.2
1.
2.
3.
4.
www.barbecook.com
Set the control knob of one burner to HIGH.
Always light one main burner to start with. Never light all
main burners at the same time.
lf the burner does not light within 5 seconds, set its control
knob to OFF, close the gas supply and wait 5 minutes. This
allows any accumulated gas to escape.
Retry lighting the burner. lf it still does not light, refer to "14
Troubleshooting" to determine the cause of the problem.
Once one burner is lit, light the other burners by setting their
control knobs to HIGH.
The side burner can only carry pots with a maximum
weight of 9 kg, maximum diameter of 220 mm and
minimum diameter of 120 mm.
U
sing the igniter
Open the lid and set the control knob of the side burner to
OFF.
If no other burner is lit yet, open the gas supply and wait ten
seconds. This allows the gas to stabilize.
Push in the control knob of the side burner, set it to HIGH
and hold it for a moment. The build-in igniter will cause
sparks, which will light the side burner.
If the burner does not light after three attempts, set its
control knob to OFF, close the gas supply and wait 5
minutes. This allows any accumulated gas to escape.
Retry lighting the side burner. If it still does not light, try
lighting it with a match or refer to "14 Troubleshooting" to
determine the cause of the problem.
U
sing a match
Place a match in the match holder.
Open the lid and set the control knob of the side burner to
OFF.
lf no other burner is lit yet, open the gas supply and wait ten
seconds. This allows the gas to stabilize.
Light the match and hold it about 13 mm from the side
burner.