Chicco Polly PROGRES 5 Mode D'emploi page 20

HOW TO USE THE CHAIR BOOSTER SEAT
The product may be used as chair booster seat from
an age at which the child can sit up unaided, until 36
months (FIG.33).
To use the product as chair booster seat:
- release the seat C from the seat base B pressing the
release buttons C1 on the sides of the seat;
- keeping the C1 buttons pressed, partially turn upwards
the front part of the seat and lift it until it is completely
released from the base (FIG.25);
- turn the seat upside down to facilitate the subsequent
operations (FIG.26);
- open the feet C10 by using the release devices C11
(FIG.27). Remove the buckles and the harness C14a-b
from their slot compartments C12 as shown in FIG.28
to be able to mount the seat on the adult chair;
- place the backrest, locking it in vertical position;
- to raise the seat, turn the feet C10 outwards until
locked in their position, releasing them by using the
devices C11 (FIG.27A). If the seat does not need to
be raised, after having removed the harness and the
buckles, close the feet, using the release devices C11
and make sure that they are correctly fastened in their
closing position (FIG.26).
WARNING: while opening and closing the feet, make
sure to always use the release devices C11 to avoid
damage to the product.
WARNING: when used as chair booster seat, always use
the backrest in vertical position only, to guarantee the
safety of your child.
WARNING: when used as chair booster seat, make sure
that both feet are correctly fastened in the open position.
Place the chair booster seat on the chair.
WARNING: when used as chair booster seat, make sure
that both feet are correctly fastened in the open posi-
tion and that the seat fixing harness is inserted inside
the holes on the feet.
To use this product, check if the chair has the minimum
sizes indicated in FIG.29. Attach the rear fastening straps
C14a, by passing them behind the chair's backrest, as
shown in FIG.30 and the lower fastening straps C14b
around the seat as shown in FIG.31; attach the straps
through the appropriate buckles, making sure that the
click signalling the correct attachment is heard.
Pull the free end of the straps to adjust the length until
they are well pulled and the chair booster seat is secure-
ly fastened in place (FIG. 32).
Once the chair booster seat is fastened securely to the
chair's seat and backrest, you can place your child in it
as follows:
- Release the buckles of the five-point safety harness
C13.
- Position the child on the chair booster seat, fastening
them in with the safety harness C13. Check that the
buckles of the harness are fastened properly.
- Adjust the length of the harness so it suits the child.
The tray may be used, fastening it to the armrests ob-
serving the indications of the corresponding chapter
reported previously.
COMPACT CHAIR BOOSTER SEAT (6m+)
HOW TO USE THE COMPACT CHAIR BOOSTER SEAT
In this mode, all indications reported in paragraph "Using
the chair booster seat" shall apply.
Additionally, the upper backrest C5 may be removed,
following the indications below:
- Open the zipper D3 on the front part of the fabric cov-
er D, in order to separate the upper backrest C5 from
the fixed backrest C4, until it is completely released
(FIG.34);
- The upper backrest C5 may be removed, by pushing
the C8 tab located on the rear side of the backrest C5
(FIG.35) and turning the backrest C5 forward to release
the inserts C7 from their slots C6 located on the side of
the backrest C4 (FIG.36);
WARNING: when used as chair booster seat, make sure
that both feet are correctly fastened in the open posi-
tion and that the seat fixing harness is inserted inside
the holes on the feet.
- If the rear zipper D4 is closed, open it to fit the main
cover D1 on the fixed backrest C4 (FIG.37);
- Then close the zipper D4 (FIG.38).
WARNING: When used as compact chair booster seat,
always use the backrest in vertical position only, to guar-
antee the safety of your child.
For transportation purposes, the fixed backrest C4 may
be tilted, using the specific tilting button C9, turning it
completely forward (FIG.39) to be carried in vertical po-
sition (FIG.40).
WARRANTY
The product is warranted against any conformity defect
in normal conditions of use as provided by the instruc-
tions for use.
The warranty shall not apply in the case of damages
caused by improper use, wear or accidental events.
For the duration of warranty on conformity defects
please refer to the specific provisions of applicable na-
tional standards in the country of purchase, where pro-
vided.
20