Black & Decker BES701 Traduction De La Notice D'instructions Originale page 17

Carrying the tool
Make sure the tool is unplugged.
u
Secure the blade at the 0° bevel angle and turn the base
u
to the right mitre angle fully
Secure the slide bars after pulling the carriage toward
u
you fully.
Lower the handle fully and lock it in the position by
u
pushing in the saw head locking pin (17).
Carry the tool by holding under the base.
u
If you remove the clamp, dust bag, etc., you can carry the
u
tool more easily.
Carry the tool with both hands holding the tool base.
u
Caution! Always secure all moving portions before carrying
the tool.
Saw head locking pin (17) is for carrying and storage
purposes only and not for any cutting operations.
Troubleshooting
Problem Possible Cause
Motor does
Saw not plugged in.
not start
Mitre table unlocked.
Angle of cut
inaccurate
Too much sawdust
under table.
Parts failure.
Cutting arm
Pivot spring not
cannot fully
replaced properly
raise, or
after service.
blade guard
Sawdust buildup.
cannot fully
close
Saw head locking pin
not set properly.
Saw blade damaged.
Blade binds,
Dull blade.
jams or
Improper blade.
shakes
Warped blade.
Saw blade damaged.
Saw blade loosened.
Saw vibrates
Saw not properly
or shakes
fastened down.
Workpiece not
properly supported.
Z
Protecting the environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to local
provisions. Further information is available at www.2helpU.com.
Solution
Check that all cords are plugged in.
Use mitre table locking lever (see
Adjusting the mitre angle section).
Vacuum or blow out dust. Wear eye
protection.
Contact service centre.
Contact service centre.
Clean and lubricate moving parts.
Check, adjust, and properly set saw
head locking pin.
Replace blade.
Replace or sharpen blade.
Replace blade.
Replace blade.
Replace blade.
Tighten arbor bolt.
Fasten saw to bench, stand or
table.
Properly support or clamp workpiece.
(Original instructions)
Technical data
Voltage
Speed
Blade outer diameter
Bore diameter
Weight
Blade thickness
Blade max. kerf
Mitre (max. positions)
Bevel (max. positions)
Max. cross-cut capacity at 90 °
Max mitre capacity at 45 °
Max. depth cut at 90 °
Max. depth cut at 45 °
BES701 - Level of sound pressure according to EN 62841:
L (sound pressure) 98 dB(A), Uncertainty (K) 3 dB(A)
pA
L (sound power) 108.0 dB(A), Uncertainty (K) 3 dB(A)
WA
Supply of Machinery (Safety)
EC declaration of conformity
MACHINERY DIRECTIVE
BES701 Sliding Compound Mitre Saw
Black & Decker declares that these products described under
"technical data" are in compliance with: 2006/42/EC,
EN 62841-1:2015+A11:2022,
EN IEC 62841-3-9:2020+A11:2020
These products also comply with Directive
2014/30/EU and 2011/65/EU.
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of
Black & Decker.
ENGLISH
BES701 Type 1
V
/min
mm
mm
kg
mm
mm
°
°
mm
mm
mm
mm
o
Patrick Diepenbach
General Manager, Benelux
Black & Decker,
Egide Walschaertsstraat 14-18
2800 Mechelen, Belgium
12/04/2023
230
4800
216
30
12.1
2.6
2.8
+/- 47
47
220
155
70
40
17