Publicité
Les langues disponibles
Les langues disponibles
Connection to PS •Data Compatible Equipment
Note the following when connecting the Disk Recorder to equipment with PS
q Connect the controller and PS
w Set the termination to ON for the units at both ends of the PS
Use the MODE selector on the rear of the WJ-HD500A Disk Recorder to set the termination.
e Use the optional RS-485 cable for connection.
Note: To be able to use PS
MODE Selector Setting
• Set DIP switch 4 of the MODE selector as follows for data termination.
ON: If the disk recorder is connected at the end of the PS
OFF: If the Disk Recorder is not connected at the end of the PS
Example:
• If the optional WJ-HDB502 Network Board is installed as a controller in the Disk Recorder, the system can be controlled
from a PC through the Disk Recorder.
Set DIP switch 3 of the MODE selector as follows for data termination.
ON: If the Network Board is connected at the end of the PS
OFF: If the Network Board is not connected at the end of the PS
For a system that has no system controller and is controlled through the Disk Recorder, for example, set DIP switch 3 of the
MODE selector to ON position.
Note: If the system has a system controller, set DIP switch 3 to OFF position.
24
Data equipment at the ends of the PS
•
Data mode, the communication functions need to be set up in the PS
•
RS-485 Cable
System Controller
IN
SPOT
OUT
OUT
MULTI SCREEN OUT AUDIO
16
15
14
IN
OUT
16
15
14
System Controller
Termination : ON
GEN-LOCK OUT
IN
EXT STORAGE
COPY
SIGNAL GND
REMOTE(WV-CU50)
SPOT
DATA
10/100
AC
SERIAL
BASE-T
OUT
IN
OUT
MULTI SCREEN OUT AUDIO
CONTROL
ALARM
MODE
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
IN
ON
OFF
OUT
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
POWER
VIDEO
Disk Recorder
Data line.
•
Data line.
•
Data line.
•
RS-485 Cable
MODE Selector
GEN-LOCK OUT
EXT STORAGE
COPY
SIGNAL GND
REMOTE(WV-CU50)
DATA
10/100
BASE-T
AC
SERIAL
IN
CONTROL
ALARM
MODE
13
12
11
10
9
8
7
6
5
4
3
2
1
ON
OFF
13
12
11
10
9
8
7
6
5
4
3
2
1
POWER
VIDEO
Disk Recorder
Data line.
•
Data line.
•
RS-485 Cable
MODE Selector
(3 : ON, 4 : OFF)
ON
1 2 3 4
Data Multiplex Unit
Data capability.
•
Data line.
•
(3 : OFF, 4 : OFF)
POWER
ON
OFF
ON
1 2 3 4
Data Multiplex Unit
Termination : ON
RS-485 Cable
UNIT
ALARM
POWER
0
ALARM
POWER
RESET
SUSPEND
SET UP
ALARM
SUSPEND
SET
ESC
ON
ON
OFF
1
2
3
4
OFF
Data Multiplex Unit WJ-MP204
Data Multiplex Unit
Termination : OFF
Termination : ON
Data SETUP menu.
•
UNIT
ALARM
0
ALARM
RESET
SUSPEND
SET UP
ALARM
SUSPEND
SET
ESC
1
2
3
4
Data Multiplex Unit WJ-MP204
UNIT
ALARM
0
ALARM
RESET
SUSPEND
SET UP
ALARM
SUSPEND
SET
ESC
1
2
3
4
Data Multiplex Unit WJ-MP204
Publicité
