Triton T12OT Instructions D'utilisation Et Consignes De Sécurité page 7

d) Under abusive conditions, liquid may be ejected from the battery;
avoid contact. If contact accidentally occurs, flush with water. If
liquid contact eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns.
Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
WARNING: Before connecting a tool to a power source (mains switch power
point receptacle, outlet, etc.) be sure that the voltage supply is the same as
that specified on the nameplate of the tool. A power source with a voltage
greater than that specified for the tool can result in serious injury to the user,
and damage to the tool. If in doubt, do not plug in the tool. Using a power
source with a voltage less than the nameplate rating is harmful to the motor.
Oscillating Multi-Tool Safety
WARNING: Contact with electric or gas lines can lead to fire, electric shock
and explosions. Penetrating a water line can result in damage to property and
electric shock. Use appropriate detectors to determine if utility lines are hidden
in the work area. Always be extremely careful when making blind and pocket
cuts where the exit point of the blade or accessory at the other side of the
material cannot be seen.
WARNING: Asbestos may be in materials and textured coatings in older
properties and should be treated with extreme caution. If you suspect or
discover asbestos consult your local health and safety authority immediately
for advice on its removal. It may require the services of a specialist asbestos
removal company.
WARNING: If a cutting accessory makes contact with a 'live' wire, the exposed
metal parts of the power tool may become 'live' and could give the operator
an electric shock. Hold the power tool by the insulated gripping surfaces at all
times during use.
WARNING: DO NOT work with damp or wet materials or accessories that
require liquid coolants. Liquids entering the body of the tool is an electrical
hazard as well as likely to destroy the tool.
WARNING: The dust produced from working with some materials can be toxic.
Beech, oak, mahogany and teak natural woods, man-made composite woods
and some surface treatments including paint with lead are toxic. Lead based
paint is common in buildings pre 1960. Always wear suitable respiratory
protection for example a respirator face mask. Ideally also use a dust
extraction system or regularly vacuum the work area to prevent the build-up
of dust and do a final vacuum after the work is completed. Most dust is a fire
hazard. Overhead work surfaces have an increased safety risk for dust.
• Wear protective, cut-proof gloves when changing blades and accessories.
Some blades and accessories can be very sharp. Scraper blades sharpen
as they are used. Blades and accessories shortly after use can be very hot,
allow to cool
• Keep your workplace clean. Dusts created from different materials
including woods and metals can be highly flammable. Dust from light
alloys including magnesium can burn or explode easily
• DO NOT treat the work surface with fluids containing solvents. If such
fluids become warm from scraping, toxic vapours may be produced, or
surfaces may catch fire
WARNING: Never fit any blade or accessory with a maximum speed lower than
the no load speed of the power tool.
• Only change accessories and blades or perform maintenance with the tool
disconnected from its power supply, either mains connection or battery. If
the tool features a captive battery in a charged state take extra care not to
switch it on accidentally when changing accessories or blades
• Always use accessories or blades that are approved by the manufacturer or
GB
meet the specification of your power tool, this includes being compatible in
size and speed. DO NOT try to cut material thicker than the capacity stated
in the specification
• Only use an adapter for using different accessories or blades if the adapter
is specifically designed and approved by the manufacturer of your power
tool
• DO NOT modify accessories or blades so they work with power tools they
were not intended to work with or for uses that they were never designed
for
6
350766_Z1MANPRO1_NEW_V2-USA.indd 6
• DO NOT use accessories or blades that are damaged, bent, chipped,
cracked, heavily corroded or excessively worn. Such accessories can break
apart in use causing injury to the operator. Always inspect accessories or
blades before use and discard immediately if not in good condition. Never
use blades that are worn to a dull edge. Always use sharp blades
• Always ensure all accessories or blades are securely attached to the tool
before use and the securing tool is removed prior to use
• DO NOT attempt to free a jammed blade or accessory until the power tool
has been disconnected from power
• Inspect the workpiece before use to make sure it is in the correct condition
for the fitted accessory or blade. Remove all nails, staples and other
embedded objects prior to starting work
• Any freely movable workpieces should be secured with a clamp or vice
before starting work
• Always ensure that the lighting is adequate in the work area. Never remove
your safety goggles or glasses to improve your view instead increase the
level of lighting or move the lighting so it specifically illuminates the work
area correctly
• DO NOT operate the power tool near flammable materials. Be especially
careful when cutting wood and metal. Sparks from metal cutting are a
common cause of wood dust fires
• If batteries are to be charged outdoors, ensure that the power supply and
charger are protected against rain and moisture
• NEVER start the power tool while the blade or accessory is in contact with
the workpiece, and always allow the power tool to reach its full speed
before making contact with the workpiece. Use the variable speed control
of the tool (if fitted) to start the tool at the correct speed for the accessory
or blade fitted
• DO NOT exert additional pressure on the body of the tool: allow the blade or
accessory to do the work. By not exerting additional pressure you maintain
a safer stronger grip on the power tool when it breaks through the material,
as well as reducing wear on the power tool which will extend the power
tool's service life. Additional pressure may also bend or twist the accessory
or blade which may cause it to break and cause injury. If the power tool
allows for being held with one or two hands hold with two hands whenever
possible. Always exercise caution when handling this power tool
• Sawing, cutting and abrasive actions create heat. This may affect the
workpiece and power tool. Always monitor the heat level and in the
event of excessive heat switch off the power tool and allow to cool before
restarting work. Some power tools depending on design may be more
quickly and effectively cooled by running at high speed without load
• The power tool will draw in dust through the vents on its body. Excessive
accumulation of powdered metal may cause an electrical hazard and
destroy the tool. Always ensure the environment dust level is safe for the
tool and ensure the vents are not blocked
• For mains-operated power tools, ensure the cable of the power tool is
always kept behind the tool and never close to where the accessory or
blade is operating
• DO NOT reach under the workpiece, rest the workpiece on your body,
or hold the workpiece while working on it, as contact with the blade or
accessory protruding from the workpiece can result in serious injury
• Anti-vibration gloves should be worn when operating power tools that
produce large amount of vibration, especially during long-term use
• For power tools with a rotating mechanism and accessories ensure the
operator is not wearing clothes or gloves with frayed threads, cords etc.
that could be entangled in the rotating mechanism dragging the operator's
hand into the rotating accessory causing injury. ALWAYS wear tight fitting
work clothes, safety shoes. Remove jewellery and secure long hair. Never
wear fabric-based gloves that can produce strands of material when
operating this type of power tool
• DO NOT allow sanding sheets to wear away on the sanding pad. This will
damage the surface of the pad requiring replacement and may cause parts
of the sanding sheet to fly off the pad, causing operator injury
• DO NOT touch the moving sanding sheet
• Wire brush bristles are thrown by the brush even during ordinary operation.
DO NOT overstress the wires by applying excessive load to the brush. The
wire bristles can easily penetrate light clothing and skin
26/09/2014 08:53