Stiebel Eltron WPM 234727 Guide Des Menus Et Messages page 15

NOTIFICATION LIST
WPM (CN) 234727, 239693
Message code Notifica-
tion from
30186 WPM
30188 WPM
30189 WPM
30190 WPM
30191 WPM
30192 WPM
30193 WPM
30196 WPM
30197 WPM
30198 WPM
30199 WPM
30201 WPM
30202 WPM
30203 WPM
30204 WPM
30205 WPM
30206 Heat pump
30207 WPM
30208 WPM
30209 WPM
30210 WPM
30211 WPM
30212 WPM
30213 WPM
30214 WPM
30215 WPM
30216 WPM
30217 WPE
30218 WPE
30219 WPE
30220 WPE
30221 WPE
WPMsystem
Reason for fault code being triggered
The heating circuit pump on the MFG cannot be
switched.
The 3-way diverter valve in the MFG cannot be
switched.
The emergency/booster heater in the MFG cannot
be switched.
Incorrect communication with the HP return tem-
perature sensor in the MFG.
Incorrect communication with the HP flow tempera-
ture sensor in the MFG.
Incorrect communication with the NHZ flow sensor
in the MFG.
Incorrect communication with the DHW tempera-
ture sensor in the MFG.
Incorrect communication with the heating circuit
flow rate sensor in the MFG.
Incorrect communication with the brine circuit flow
rate sensor in the MFG.
Incorrect communication with the heating circuit
pressure sensor in the MFG.
Incorrect communication with the brine pressure
sensor in the MFG.
Incorrect communication with the heating circuit
pump in the MFG.
Incorrect communication with the brine pump in
the MFG.
Incorrect communication with the 3-way diverter
valve in the MFG.
Incorrect communication with the emergency/
booster heater in the MFG.
Incorrect communication with the MFG.
Sensor value of "current sensor" outside the permis-
sible range
Sensor value of "outside temperature sensor" out-
side the permissible range
Sensor value of "buffer temperature sensor (heating
circuit sensor 1)" outside the permissible range
Sensor value of "flow temperature sensor" outside
the permissible range
Sensor value of "heating circuit sensor 2" outside
the permissible range
Sensor value of "heating circuit sensor 3" outside
the permissible range
Sensor value of "DHW cylinder sensor" outside the
permissible range
Sensor value of "source sensor" outside the permis-
sible range
Sensor value of "heat source 2" outside the permis-
sible range
Sensor value of "flow cooling sensor" outside the
permissible range
Sensor value of "DHW circulation temperature sen-
sor" outside the permissible range
Sensor value of "swimming pool sensor, primary"
outside the permissible range
Sensor value of "swimming pool sensor, secondary"
outside the permissible range
Sensor value of "heating circuit sensor 4" outside
the permissible range
Sensor value of "heating circuit sensor 5" outside
the permissible range
Sensor value of "DHW cylinder 2 sensor" outside the
permissible range
Possible cause of fault / remedy
Check the communication cable terminal or replace
the communication cable.
Check the communication cable terminal or replace
the communication cable.
Check the communication cable terminal or replace
the communication cable.
Check the communication cable terminal or replace
the communication cable.
Check the communication cable terminal or replace
the communication cable.
Check the communication cable terminal or replace
the communication cable.
Check the communication cable terminal or replace
the communication cable.
Check the communication cable terminal or replace
the communication cable.
Check the communication cable terminal or replace
the communication cable.
Check the communication cable terminal or replace
the communication cable.
Check the communication cable terminal or replace
the communication cable.
Check the communication cable terminal or replace
the communication cable.
Check the communication cable terminal or replace
the communication cable.
Check the communication cable terminal or replace
the communication cable.
Check the communication cable terminal or replace
the communication cable.
Check the communication cable terminal or replace
the communication cable.
Check sensor, leads and the relevant plug-in con-
nectors, and replace if faulty.
Check sensor, leads and the relevant plug-in con-
nectors, and replace if faulty. Terminal: WPM X 1.3
Check sensor, leads and the relevant plug-in con-
nectors, and replace if faulty. Terminal: WPM X 1.4
Check sensor, leads and the relevant plug-in con-
nectors, and replace if faulty. Terminal: WPM X 1.5
Check sensor, leads and the relevant plug-in con-
nectors, and replace if faulty. Terminal: WPM X 1.6
Check sensor, leads and the relevant plug-in con-
nectors, and replace if faulty. Terminal: WPM X 1.7
Check sensor, leads and the relevant plug-in con-
nectors, and replace if faulty. Terminal: WPM X 1.8
Check sensor, leads and the relevant plug-in con-
nectors, and replace if faulty. Terminal: WPM X 1.9
Check sensor, leads and the relevant plug-in con-
nectors, and replace if faulty. Terminal: WPM X 1.10
Check sensor, leads and the relevant plug-in con-
nectors, and replace if faulty. Terminal: WPM X 1.11
Check sensor, leads and the relevant plug-in con-
nectors, and replace if faulty. Terminal: WPM X 1.12
Check sensor, leads and the relevant plug-in con-
nectors, and replace if faulty. Terminal: WPE X3.4
Check sensor, leads and the relevant plug-in con-
nectors, and replace if faulty. Terminal: WPE X 3.5
Check sensor, leads and the relevant plug-in con-
nectors, and replace if faulty. Terminal: WPE X 3.6
Check sensor, leads and the relevant plug-in con-
nectors, and replace if faulty. Terminal: WPE X 3.7
Check sensor, leads and the relevant plug-in con-
nectors, and replace if faulty. Terminal: WPE X 3.8
V2.3 | 15