Important Safety Instructions; Technical Data - BorMann PRO BBC4020 Mode D'emploi

EN EN

Important Safety Instructions

WARNING ! READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below, may result in electric shock, fire and /or serious personal injury.
Safety precautions for working in the vicinity of a battery
1) Batteries generate explosive gases during normal operation. Use in well-ventilated area.
2) Consider having someone close enough or within the range of your voice to come to your aid when you work near a battery.
3) Do NOT smoke, strike a match, or cause a spark in vicinity of battery or engine. Avoid explosive gas, flames and sparks.
4) Remove all personal jewelry, such as rings, bracelets, necklaces, and watches while working with a vehicle battery. These items may produce a short-circuit
that could cause severe burns.
5) Be extra cautious to reduce risk of dropping a metal tool onto the battery. It might spark or short-circuit a battery or other electrical hardware which may
cause an explosion or fire.
6) Wear complete eye protection, hand and clothing protection. Avoid touching eyes while working near a battery.
7) Study all battery manufacturer's specific precautions such as removing or not removing cell caps while charging and recommended rates of charge.
8) Clean battery terminals before connected with the charger. Be careful to keep corrosion from coming in contact with eyes.
9) When it is necessary to remove a battery from vehicle to charge, always remove grounded terminal from battery first. Make sure all accessories in the vehicle
are off in order to prevent an arc.
10) It is NOT intended to supply power to an extra-low-voltage electrical system or to charge dry-cell batteries. Charging dry-cell batteries may burst and cause
injury to persons and property.
11) NEVER charge a frozen, damaged, leaking or non-rechargeable battery.
12) If battery electrolyte contacts skin or clothing, wash immediately with soap and water. If an electrolyte enters eye, immediately flood eye with running clean
cold water for at least 15 minutes and get medical attention immediately.
Safety precautions for using the charger
1) Do NOT place the charger in the engine compartment or near moving parts or near the battery; place as far away from them as DC cable permits. NEVER
place a charger directly above a battery being charged; gases or fluids from battery will corrode and damage charger.
2) Do NOT cover the charger while charging.
3) Do NOT expose to rain or wet conditions.
4) Connect and disconnect DC output only after setting AC cord from electric outlet.
5) Use of an attachment not recommended or sold by the manufacturer may result in a risk of fire, electric shock or injury to persons.
6) Do not overcharge batteries by selecting the wrong charge mode.
7) To reduce the risk of damage to electric plug and cord, pull by the plug rather than the cord when disconnecting charger.
8) To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning.
9) Operate with caution if the charger has received direct hit of force or been dropped. Have it checked and repaired if damaged.
10) Any repair must be carried out by the manufacturer or an authorized repair agent in order to avoid danger
BBC4020 charger
1) The BBC4020 charger is designed for charging 12V/24V lead-acid and 12V lithium-ion batteries (LIFEPO4).
2) Built-in intelligent microprocessor makes charging faster, easier and safer.
3) This charger has safety features, including spark proof, protection for reverse polarity, short circuit, overheat and overcharge.
4) When starting, the battery voltage type is 12V by default. The user can select battery voltage type by pressing "12V/24V" button in standby.
5) When starting, the charger works for STD battery type by default. The user can select battery type including STD, COLD/AGM, CAL, LIFEPO4 (only for 12V
battery) by pressing and holding "FUNCTION/TYPE" button for 3 seconds in standby.
6) When the charger is powered on, it enters the standby mode by default. The user can select functions including CHARGE, SUPPLY, REPAIR by pressing
"FUNCTION/TYPE" button. The charger's technical specifications can be seen below:

Technical Data

Model BBC4020
Input 220-240 V AC, 50/60 Hz, 1 A, 120 W MAX
Output 12 V DC, 7 A / 24 V DC, 3.5 A
Ba ery capacity 14 - 230Ah (12V) / 14 - 115 Ah (24V)
8 steps, Full-automa c Charging Cycle, Lowest Chargeable
Voltage 3V, Cold /AGM Mode, 12 V / 24 V Dedicated Repair
Charger Type
Mode, ALT - Check func on, CCA Test func on, Supply Mode
13.6 V / 5 A
12V & 24V lead - acid ba eries (WET/MF/CA/EFB/GEL/AGM),
Ba ery Types
12V lithium ba eries
Housing protec on IP54
Independent selec on mode for 12V/24V ba ery and memory
Features func on with LCD screen, Detailed error lights to remind the
abnormal processes
2
WWW.NIKOLAOUTOOLS.GR
* The manufacturer reserves the right to make minor changes to product
design and technical specifi ca ons without prior no ce unless these changes
signifi cantly aff ect the performance and safety of the products. The parts
described / illustrated in the pages of the manual that you hold in your hands
may also concern other models of the manufacturer's product line with
similar features and may not be included in the product you just acquired.
* To ensure the safety and reliability of the product and the warranty validity,
all repair, inspec on, repair or replacement work, including maintenance
and special adjustments, must only be carried out by technicians of the
authorized service department of the manufacturer.
* Always use the product with the supplied equipment. Opera on of the
product with non-provided equipment may cause malfunc ons or even
serious injury or death. The manufacturer and the importer shall not be
liable for injuries and damages resul ng from the use of non-conforming
equipment.