JB Systems Light CMX-24 Mode D'emploi page 9

ENGLISH

Show Scene
You can recall a scène in the Chase/Scenes mode. Be sure that:

The Chase/Scenes mode is activated (by using the <MODUS SELECT/REC SPEED> button)

The {Master B} fader is at its lowest position

MIX Chase is activated; select this by using the <PARK> button, just on top of the MASTER B
fader in Chase/Scenes mode. The [MIX CHASE] led is situated above the FADE fader and must
be lit.

The Black-out function is not activated.

All the PRESET faders (A & B) are set at their lowest position.
Move the {PRESET B 1} fader to its highest position. The stored scene will appear on the green Leds (and
on your projectors).
By setting several Preset B faders at the same time on a position that is higher than 0, you can create a
combined scene. You can modify the intensity of the scene by using the Master B fader.
You can quickly set the scenes at 100% by using the Preset B flash buttons. Repeat the procedure to store
scenes in page 2. Be sure that the Preset B faders 1 to 3 of page 2 contain also scenes (make them different
from the other scenes). Check also these scenes.

Page to page
Now you have scenes for the preset B faders 1 to 6 from page 1 and the preset B faders 1 to 3 from page 2.
The preset faders 1 to 3 can now show 2 different scenes, depending of the selected page.
Execute the next position:

Move all the {Preset B} faders to the lowest position.

Activate page 1 by using the <PAGINA/REC CLEAR> button

Move {Preset B 1} fader 1 to the highest position. The stored scene is shown.

Activate Page 2 by using the <PAGINA/REC CLEAR> button

The same scene is still shown.

Move the {Preset B 1} fader to the lowest position.

Move the {Preset B 1} fader to the highest position. The scene stored in preset B 1 of page 2 is
shown.

The content of the Preset B fader has changed. This happened when the fader was in its lowest
position.

Modify a Scene
If you need to have another scene, you can:

Compose a completely new scene and store it

Adapt a scene by modifying the intensity of certain channels
Follow the normal procedure to store a scene. when you have stored the working memory in the Preset B
fader by pressing <RECORD/SHIFT> + <PRESET B x>, the old scene will be replaced by the new scene.
If only a few channels of a scene need to be adapted, it is easier to recall the scène and to adapt it than to
create a complete new scene. The CMX24 has a special edit mode that allows you to modify the channels of
a scene.
First of all, you need to place the Preset B fader with the stored scene in edit mode:

Be sure that program mode is activated.

Be sure that Chase/Scenes mode is activated.

Bring all the Preset A faders to their lowest position

Select a page by using the <PAGINA/RECCLEAR> button

Place the Preset B fader in edit mode:
Press and hold the <EDIT/ALL REV> button
o
Press and release the <PRESET B x> button. X has to be replaced by 1, 2, 3, 4, 5, 6, 7,
o
8, 9, 10, 11 or 12 depending of the preset B fader that you want to edit
o Release the <EDIT/ALL REV> button
The yellow led on top of the Preset B fader will Lit and the actual scène is shown.
o
Increase the intensity of channels:

Press and hold the <UP/CHASE REV> button

Press and hold the <PRESET A x> button of the channel where you want to have the intensity
increased
JB SYSTEMS 13/93
®
OPERATION MANUAL
CMX24
ENGLISH

Use the <PRESET B x> button for the channels 13 to 24.

The intensity will slowly increase on you fixtures and on your display

Release the buttons, as soon as you have reached the desired intensity.
Reduce the intensity of channels:

Press and hold the <DOWN/BEAT REV> button

Press and hold the <PRESET A x> button of the channel where you want to have the intensity
reduced

Use the <PRESET B x> button for the channels 13 to 24.

The intensity will slowly decrease on your fixtures an on your display.

Release the buttons as soon as you have reached the desired intensity.
!! The intensity that you have set will be directly stored, it is not possible to undo the modifications.
To Exit the Edit mode:

Press and hold the <RECORD/SHIFT> button

Press and release the <KILL/REC EXIT> button

Release the <RECORD/SHIFT> button

The normal output is shown.

Store a Chase
A chase is a succession of scenes that are shown on a certain rhythm.
The controller makes no difference between scenes and chases. A scene is in fact a chase with only 1step.
So you will notice that the method of storing a chase is almost identical to the method of storing a scene.
(At this time, program mode has to be active, if it is not; you will have to do that first)
Be sure that the working memory is emtpy:

Press and hold the <RECORD/SHIFT> button

Press and release the <PAGINA/REC CLEAR> button

Release the <RECORD/SHIFT> the
We are going to make a chase, composed out of 4 scenes. Be sure that you work in program mode and that
your master is not set to 0.
Scene 1
Set the first scene:

Channel 1 = 100%

All the other chanels = 0%
Now store this scene in the working memory:

Press and release the <RECORD/SHIFT> button

[001] appears on the display = first scene
Scene 2
Set the second scene:

Channel 2 = 100%

All the other channels = 0%
Now store this scene in the working memory:

Press and release the <RECORD/SHIFT> button

[002] appears on the display = second scene
Scene 3
Set the third scene:

Channel 3 = 100%

All the other channels = 0%
Now store this scene in the working memory:

Press and release the <RECORD/SHIFT> button

[003] appears on the display = third scene
Scene 4
Set the fourth scene:

Channel 4 = 100%

All the other channels = 0%
Now store this scene in the working memory:
JB SYSTEMS 14/93
®
OPERATION MANUAL
CMX24