JB Systems Light CMX-24 Mode D'emploi page 12

ENGLISH
The easiest way to test this is to activate a chase (by using a preset B fader), then place one of the cannels
in BLIND. Now you can adapt the intensity by using the preset A fader. This channel will not follow the chase
anymore. However, the FULL-ON button will still activate the channel.
To place the channel back in normal mode:
Press and hold the <HOME> button
o
Press and release the <Preset A x> button
o
Release the <HOME> button
o

Preset B
To disconnect the channels 13 to 24 from the preset B scenes/chases:
Press and hold the <BLIND> button
o
Press and release the <Preset B x> button
o
Release the <BLIND> button
o
The level will only be determinated by using the preset B fader, master A fader and the flash buttons.
You can set the intensity of the channel by using the preset B fader. The preset B fader will not be linked
anymore to its stored scene/chases.
To place the channel back in normal mode:
Press and hold the <HOME> button
o
Press and release the <Preset B x> button
o
Laat de <HOME> toets los
o
o You will notice that the Preset B fader is directly used to activate the programmed
scene/chase. That's why it is better to place the de Preset B fader in the lowest position,
before to activate the normal mode
SINGLE CHASE
De single chase mode is useful to create quickly different chases.
When Single chase (indicate with the PARK button) is activated, the CMX24 will create chase, based on all
the preset B faders that are not set to zero. Each preset B fader will be activated till all the fader positions are
shown. Then, the next preset B fader will be shown.
In this text, we consider that all the preset B faders in output 1 have a scene (1 to 6) or a chase (7 to 12)
stored.
Place the controller in Single Chase mode:

Bring all the Preset A and B faders to the lowest position

Be sure that the Chase/Scenes mode is activated

Press and release the <PARK> button on top of the Master B fader

The [SINGLE CHASE] Led on top of the {FADE} fader must be lit, if it is not, you will have to
press again the <PARK> button
To have a clear view of the effect you should first place the {FADE} fader in highest position and move the
{SPEED} fader till the display shows [1.05] (1,05 second).
Bring the preset B faders 1 to 4 to their highest position. Now you see a chase, composed of 4 scenes that
are stored in the faders. You can set the speed by using the {SPEED} fader, the <STEP> button and the
<TAP SYNC> button. By moving the preset B faders you can modify the chase. Try also to activate the
preset B 7 to 12 faders.
Like this you can quickly create several chases by combining scenes/chases that are stored in the preset B
faders.
Notice:

If the preset B fader includes a speed setting (stored with REC SPEED), it will not be used.

You can reverse the chase direction of the preset B faders with the REV ALL, REV ONE,
CHASE REV and BEAT REV buttons, but you can not reverse the global chase, this one always
goes from preset B 1 to preset B 12

Sometimes it looks like if the chase includes extra steps. You have to be sure that the preset B
faders are set to zero. Control this with the display.

Pressing the flash buttons of the preset B faders will add presets to the chase, sop you will have
to wait till the chase activates the preset
JB SYSTEMS 19/93
®
OPERATION MANUAL
CMX24
ENGLISH
MIDI function:

Set the MIDI IN channel: Press and hold the Record button and press 3x Flash button 1. The
display will show "CHI". Press one of the Flash buttons (1-16) to assign the MIDI in channel (1-
16). If the relevant channel LED is lit, the MIDI IN channel is correctly set.. Press and hold the
Record button and press the Exit button to exit MIDI setup.

Set the MIDI OUT channel: Press and hold the Record button and press 3x Flash button 2.
The display will show "CHO". Press one of the Flash buttons (1-16) to assign the MIDI out
channel (1-16). If the relevant channel LED is lit, the MIDI OUT channel is correctly set. Press
and hold the Record button and press the Exit button to exit MIDI setup.

Receive MIDI file dump: Press and hold the Record button and press 3x Flash button 3. The
display will show "IN", indicating the controller is ready to receive the file dump.

Send MIDI file dump: Press and hold the Record button and press 3x Flash button
display will show "OUT", indicating the controller is ready to send the file dump.

IMPORTANT:
During a file dump, the other functions of the CMX24 will not work. You will be able to use
o
them again as soon as the file dump is completed
WORKMODES
(SEE PREVIOUS PART)

Activate the secured mode
<RECORD/SHIFT> + <KILL/REC EXIT> till the Led on top of the record button goes out.
In this mode it is not possible to modify chases/scenes programs.

Activate the program mode

Press and hold the <RECORD/SHIFT> button

Press and release the <PRESET A 1> button

Press and release the <PRESET A 5> button

Press and release the <PRESET A 6> button

Press and release the <PRESET A 8> button

Release the <RECORD/SHIFT> button

Activate edit mode
<EDIT/ALL REV> + <PRESET B x>
!! This is only possible if the program mode is activated.

Delete all
!! This will erase the complete memory !!
The program mode must be activated !!

Press and hold the <RECORD/SHIFT> button

Press and release the <PRESET A 1> button
JB SYSTEMS 20/93
®
OPERATION MANUAL
4. The
CMX24