R&G LP0149BK Instructions De Montage page 6

nyloc nut (item 3) over the exposed end of each thread and tighten evenly, as shown in pictures 12
& 13. The licence plate should now be located securely in place.

To fit the R&G Mini Indicators, take TB0146 Part 3 (item 7) and fit the mini indicators through the
holes on either side before fitting the nut on the reverse. (Please use the heatshrink (item 11) to
protect the indicator wires), as shown in picture 14.

Take the indicator bracket assembly and offer up to the underside of the tail tidy. Take the three
M6 x 6mm long button head bolts (item 6) and insert through the three holes in the indicator
bracket and tighten into the three threaded holes on the licence plate bracket, before tightening
evenly. The bracket should now be securely mounted.

Feed the indicator wiring and licence plate illuminator wiring through the rubber grommet and up
into the rear section of the bike. Use the previously mounted cable tie to secure the wires together,
before tightening and trimming any excess, as shown in picture 15.

Using the cable ties and self-adhesive clips supplied, neatly tie any extra wiring together.

Connect the wiring connectors to the OEM rear loom previously removed. The rear licence plate
illuminator will fit to the rear loom using newly fitted bullet connectors, whilst the indicators will
connect directly using the original bullet connectors on the OEM loom. Re-connect to the bikes
main loom and check the correct operation of all lights (if illumination fails on any connector,
swap the bullet connections around).

Re-fit the pillion seat.

Re-fit licence plate (it may require drilling).

IMPORTANT: IF FITTING A FULL-SIZE LICENCE PLATE AND PLACING IT FAR DOWN ON THE
LICENCE PLATE HANGER, THERE IS A SMALL CHANCE OF THE LICENCE PLATE HITTING THE
BACK WHEEL UNDER HEAVY LOAD AND OVER LARGE BUMPS IN THE ROAD. IT IS YOUR
RESPONSIBILITY TO CHECK FOR THIS POSSIBILITY AND TAKE AVOIDING ACTION. FAILURE TO
CHECK THIS COULD RESULT IN SERIOUS INJURY.

Depending on local laws, attach enclosed reflector in an appropriate location.

Test the license plate illuminator and all lights before riding.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The
Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those
in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its
particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any
fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a
replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise
than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or
neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or
the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable
condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc.
P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of discontinued
products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 2 05/07/13 (AR)
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com Email: info@rg-racing.com