Rear View; Remote Control - VINCENT SV-234 Manuel D'utilisation

REAR VIEW

12
9. SPEAKER: Loudspeaker terminals
At these output sockets with threaded terminals
one or two pair(s) of stereo loudspeakers can
be connected. Speaker cable with 4 mm banana
plugs can be used. Please take note of the infor-
mation given in the section "Installation", if two
pairs of loudspeakers will be connected to the
amplifier.
10. INPUT ("LINE1"..."LINE4"): Terminal
for stereo audio signals of the source
equipment Here you find four stereo RCA
input sockets for source equipment with analo-
gue stereo (line level) audio output.
11. MAIN INPUT ("LINE5"): Main Amplifier
Input This is for the connection of a stereo
preamplifier or source equipment with a pream-
plifier output. Note that no high level output
should be connected from a stereo source to
"LINE5". This input must also not be connected
to the neighbouring preamplifier output, "PRE
OUTPUT" (14).
12. INPUT "BALANCED": XLR-Input
These are the input sockets for one stereo
audio source equipped with XLR output sockets.
13. REC OUTPUT: Output connectors
assigned to a recording device
If desired, you can connect a recording device
Vincent
28
9
10 13
16
14 15 11
like a CD recorder or a tape recorder to this
output. The stereo signal of this output is identi-
cal to the output signal of the selected audio
source at one of the inputs "LINE1"..."LINE4".
The signals of the inputs "BALANCED" and
"LINE5" are not available for recording at
this output!
14. PRE OUTPUT: Preamplifier Output
If one of the inputs "LINE1"..."LINE4" (10) or the
input "BALANCED" (12) is selected, the "PRE"
output can supply two additional main amplifier
channels with the preamplified stereo audio
signal of the selected source. The output must not
be connected to the neighboring power ampli-
fier input "LINE5 MAIN INPUT" or to the high
level input of another HiFi component.
15. POWER CONTROL (12V)
These jack connectors (3,5 mm) send and
receive the signals for the standby control
(12V Trigger).
16. AC power connector and fuse holder
To establish the power supply, connect the plugs
of the power cable to the device and to a 230V
AC wall outlet. The small plastic housing beneath
the plug opening holds the fuse. Refer to the
security precautions.

REMOTE CONTROL

Point the front of the remote control directly at
the front of the appliance, making sure there
are no objects between the remote control and
the appliance.
The distance between the remote control and the
appliance should not be more than 7 m, as the
reliability of the remote control is affected beyond
this range.
BATTERIES
Using batteries
Handling batteries incorrectly can cause battery
acid to escape or an explosion in extreme cases.
The batteries must be correctly inserted taking note
of the polarity, which is marked in the inside of the
battery compartment.
In order to make full use of the batteries' life, do
not mix new and used batteries. Make sure that
you insert batteries of the same type.
Some batteries are rechargeable, others are not
however. Take note of the precautions and instruc-
tions that are included on all batteries.
Remove the batteries if the remote control is not
going to be used for a long time.
Under no circumstances must batteries be short-cir-
cuited, taken apart or heated up.
For environmental reasons, used batteries should
be disposed of in accordance with local environ-
mental regulations and not put with domestic
waste.
Only use AAA (LR3) size batteries.
Make sure that you do not point the remote control
at an angle to the appliance, as beyond an angle
of ±30° to the centre axis the appliance may not
respond as well to the remote control. Change
both batteries if the distance at which the remote
control can be used effectively decreases.
Changing/Inserting batteries:
a) Open and remove the battery compartment lid of
the remote control by tugging sharply on the fishpla-
te on the edge of the remote control. The battery
compartment lid is held in place magnetically, there
is no need to loosen the screws!
a
b) If necessary, remove used batteries and insert
new ones correctly as shown by the diagram in
the battery compartment.
old
new
b
c) Put the compartment cover back on and close the
battery compartment.
c
Vincent
29