Technical Specifications; Glossary - VINCENT SV-234 Manuel D'utilisation

Symptom Possible Cause
Front panel display It has been switched off before using
does not work "DIMMER" (7).
Poor sound quality The cable connections are not tight, the
connectors are dirty or a cable is defective.
A record player has been connected to a high
level input without using a phono preamplifier.
An audio source with standard line level
output is connected to the amplifier direct
input "LINE5" (11).
No batteries inserted in the remote control,
The remote control
batteries are not inserted correctly or are
cannot perform any
depleted.
functions
The line-of-sight between the remote control
and the unit is obstructed, the range was
exceeded or the hand unit was operated from
a position too far to one side.
The unit is not switched on.
See section "Net frequency noise" in the chapter "Tips".
Humming low
frequency noise is
audible, even as
no audio source is
playing back

TECHNICAL SPECIFICATIONS

Frequency response:
Nominal Output Power at 8Ω:
Nominal Output Power at 4Ω:
Input sensitivity:
Total Harmonic Distortion:
Signal to Noise Ratio:
Input Impedance:
AC power connection type:
Inputs:
Outputs:
Dimensions:
Weight:
Colour:
Vincent
42
Countermeasure
Press the button "DIMMER" (7) one more time.
Check the cables and cable connections.
Interconnect a phono preamplifier.
Use line level audio sources only at the
inputs "LINE1"..."LINE4".
Check and replace the batteries if necessary.
Try to point the remote control at the front of
the unit only when the sight-line is clear,
within a 7-metre distance and, if possible,
facing the unit.
Switch on the unit.
20 Hz - 20 kHz ±0,5 dB
200 W
289 W
400 mV
< 0.1%
>90 dB
47 kΩ
220-240V/50Hz
4x RCA stereo, 1x RCA Main Input stereo,
1x XLR stereo, 1x Power Control (3,5 mm jack)
Speaker connectors accepting 4 speakers,
1x PRE stereo RCA, 1x REC stereo RCA,
2x Power Control (3,5 mm jack)
430 x 142 x 450 mm
20 kg
silver / black

GLOSSARY

Audio Sources/Source devices
These are the components of your HiFi system and
all other appliances, whose sound you want to hear
over the system and are thus connected to the pre-
amplifier, amplifier or receiver. This includes CD
players, DVD players, tuners (radios), cassette play-
ers, DAT recorders, personal computers, record
players, portable audio devices and many more.
Input sensitivity
Term for the smallest average (RMS) input voltage
which causes the maximum output power at the
maximum volume setting on the amplifier.
Examples: 100 mV to 500 mV (Millivolts) on high
level inputs, 2 mV to 5 mV on the phono MM input
or 0.1 mV to 0.5 mV on the phono MC input.
dB-Level
This is a way of describing any physical quantity; it
is a common measurement for signal voltages and
the volume. It is given in decibels (dB). Alternating
signal voltages below 1V (RMS) are described as
"line level" voltages, which are suitable as music
signals for amplifier inputs. Inputs on amplifiers
(mostly represented by RCA sockets), which are
designed for signals on the CD player, tape recor-
der, DVD player etc. are also referred to as "line
level inputs" or "high-level inputs". Those signal
inputs must not be confused with inputs that accept
preamplified signals.
RCA
RCA is the American name for coaxial RCA connec-
tors and sockets, originally the abbreviation for
"Radio Corporation of America", the name of a
United States company. Both the plug and cable
consist of a rod-shaped inner lead and a cylindri-
cal-shaped outer lead. This enables a mono audio
signal or a video signal to be transmitted.
Compared to the XLR plug connector, this type of
connection is also called "unbalanced signal con-
nection".
XLR
Also: "Symmetrical Connection" or "balanced".
A plug-and-socket connection for audio devices.
It is round (with approx. 1.5 cm in diameter) and
has 3 contacts/pins. XLR is an alternative connecti-
on to RCA used to transmit NF-Signals in professio-
nal audio equipment. The advantage is one additio-
nal transmission path for the same but phase inver-
ted signal. If the receiving device can process this,
all inducted noise received in the cable screen can
be eliminated. The signal voltage level used for this
type of transfer is higher, so it is a more robust less
sensitive signal path.
Vincent
43