Barbecook Brahma 4.2 Inox Instructions D'assemblage page 42

Only for Brahma 5.2
223.9352.000 – 223.9952.000
ies are not supplied)
• Store the motor in a dry place when
it is not in use
• The spit should only be used out-
doors and for its intended purpose
• Do not allow children to use the spit
WARNING:
• Never leave your barbecue unat-
tended when in use, especially in
the presence of children or domestic
animals. Regularly check the barbe-
cue for proper functioning of all its
components
Aromaz ® trays, etc.) can become
when touching these parts. Keep
young children away from the barbe-
cue.
• Never move the barbecue when in
use
• Never use charcoal, wood or bri-
quettes
• Never use lava rocks or ceramic
briquettes
TIPS FOR CLEANING AND
MAINTENANCE
To prolong the life of your appliance, it
should be cleaned carefully after every use.
To make it as easy as possible to clean
your appliance, Barbecook ®
able foil fitted in the bowl under the burn-
grease. Once your appliance has cooled
from the bowl, and cleaning your appliance
takes no time at all.
Register your appliance at
www.barbecook.com/registration so that
for your appliance at any time.
After use, you can let your appliance burn,
empty of food and with the cover closed,
for a further ten minutes with all the burners
turned to HIGH. This ensures that a large
proportion of any residues will be burnt off,
making subsequent cleaning easier. Let the
appliance cool down.
You can then remove the burnt residues
with a non-abrasive brush and clean.
42 www.barbecook.com
GRILLS AND GRIDDLES
After every use, let the barbecue cool down
and clean the grills with a non-abrasive
brush. Grills can also be washed with the
detergent or sodium bicarbonate. Do not
use oven cleaners.
To prolong the life of your appliance, you
should carry out all the activities listed be-
low, preferably at the start of the barbecue
season.
IMPORTANT
Natural hazards - spiders and insects:
very small insects might make a web
or nest in the venturi tubes of the gas
burners (fig. E).
E
This will partly or completely block the
gas supply. A smoking yellow flame, or
a burner which is difficult or impossible
to ignite, are indications that this tube is
blocked.
The gas may end up burning outside the
venturi tube and severely damage your
appliance. If this happens, shut off the
gas cylinder at once.
Cleaning the venturi tubes/burners
has developed
The burners and venturi tubes must be
removed for cleaning at least twice a year.
• Clean the venturi tubes thoroughly. Clear
any blocked opening with a pipe cleaner
• Replace the burner in accordance with
the venturi tubes must be replaced prop-
erly on the gas valves.
• If the burner is split, or displays unu-
sual holes or other damage, it must be
replaced.
®
Note: damage due to a partly or wholly
obstructed venturi tube in a burner is
not covered by the warranty and will be
regarded as inadequate maintenance.
Special precautionary measures for
enamelled parts
invalidate the warranty)
Special precautionary measures for the
stainless steel parts
invalidate the warranty)
When cleaning stainless steel or chromed
parts, it is best to avoid aggressive, abra-
cleaners and give them time to act. Always
use always a soft sponge or cloth. Rinse
thoroughly and dry well before you store
the appliance.
To prevent the formation of rust on stain-
less steel components, avoid any contact
with chlorine, salt or iron. The environ-
ment in which your appliance is used can
adversely affect its lifetime. Less suitable
locations include the coast, near railway
lines and the vicinity of a swimming pool.
F
• Metals and/or sharp objects can
damage the enamel.
• Never pour cold liquids into the hot
bowl. This can damage the enamel.
• Avoid knocking the appliance
against a hard surface. This can
damage the enamel.
• In these models, the enamelling pro-
cess sometimes leaves thin edges
which are not fully covered with
enamel. This is not regarded as a
manufacturing fault, and is therefore
not covered by the warranty.
• When assembling enamelled
parts always use the fibre washers
supplied to prevent damaging the
enamel around the screw fixings.