Barbecook Brahma 4.2 Inox Instructions D'assemblage page 40

• Once you have checked for leaks,
turn off the gas, rinse the connec-
tions with water and dry to prevent
the formation of rust.
• Turn the cylinder knob to the left to
close the cylinder.
Note: the regulator may be different
from the one illustrated here.
WARNING: You must carry out these
leak tests even if your appliance is set
up by the dealer or the shop.
REPLACING THE CYLINDER
When changing the gas cylinder, ensure
that the knobs on the barbecue are in the
closed. Do not replace the gas cylinder
close to anything that may produce a flame
or spark.
GAS CYLINDER
Although perfectly safe when handled cor-
rectly, lack of caution may result in fire and/
or explosion.
To minimise the risks:
• Never store the cylinder in a build-
ing, garage or other enclosed area,
but always in a well-ventilated area
• Never store the cylinder in the vicin-
ity of another gas operated appli-
ance, or in a very warm area, such
as a car or boat
• Always keep the cylinder out of
reach for children
• Always transport and store the cylin-
der in an upright position
• Do not smoke near the gas cylinder.
USE
Do not use the barbecue before you have
read, understood and checked all informa-
tion in this manual.
Ensure that:
• The barbecue is correctly installed
• There is no leak in the gas supply
• The burners are correctly installed,
the venturi tubes are properly placed
over the openings of the gas valves
cleaning of the burners)
• None of the gas supply hoses can
come into contact with a hot surface
• Your barbecue is installed in a safe
place
40 www.barbecook.com
D
Prior to lighting the burners, all checks and
• The lid of the barbecue must always
• Do not bend directly over the barbe-
• The control knobs of the barbecue
cylinder valve. Before opening the
control knob of one burner, wait ap-
prox. 10 seconds to allow to gas to
stabilize
• Important: first light the middle
burner
• As soon as one burner has been
lighted, you only need to put the con-
• Never try to light all burners at once
IGNITER
The battery is not supplied as standard.
• Open the lid of the barbecue
• Open the gas cylinder valve.
• Press the igniter until you hear
sparks
• Holding down the igniter, press the
control knob of the middle burner
• If the burner does not light after 3
attempts, disconnect the gas and
wait 5 minutes before trying again.
This will allow the accumulated gas
to escape. Try again, repeating the
above steps.
- • If the burner still does not light, read
to determine the cause and the rem-
edy, or use a match as described
below.
MATCH
Left and right at the bottom of the burner
box is a small opening that can be used to
light the burners with a match, if the elec-
• Open the lid of the barbecue
• Place a match in the match holder
• Hold a burning match through the
hole, approx. 13 mm from the burner
• Open the gas cylinder valve.
• Push the required control knob and
light within 5 seconds. If not, turn the
control knob off and wait 5 minutes
to allow the gas to escape.
• Repeat steps 1 through 5. If the
burner still does not light after 3
G
• As soon as the first burner has been
lighted, you only need to put the con-
THE IGNITER
To light the side burner, use the igniter on
the control panel and the control knob on
the side table.
• Press the igniter until you hear
sparks.
• Holding down the igniter, press the
control knob of the side burner and
• Repeat a number of times if the
burner does not light immediately.
• If the burner does not light after
5 seconds, turn the control knob to
-