schmalz RECB MATCH Notice D'utilisation page 81


Parameter

Device Settings

Commands
2 0x0002 0 System command

Access Control
90 0x005A 0 Extended device access locks
91 0x005B 0 Pin-Code NFC

Initial Settings
Blow-Off mode Ejector 1
69 0x0045 1
Blow-Off mode Ejector 2
69 0x0045 2
75 0x004B 1 Output filter Ejector 1, switch-off delay for SP2 and SP1
Output filter Ejector 2, switch-off delay for SP2 and SP1
75 0x004B 2

Process Settings Ejector 1

Production Setup - Profile P0 Ejector 1
68 0x0044 0 Air-Saving function
Disable continous sucking
78 0x004E 0
100 0x0064 0 Switchpoint 1 (SP1)
101 0x0065 0 Resetpoint 1 (rP1)
Switchpoint 2 (SP2)
102 0x0066 0
103 0x0067 0 Resetpoint 2 (rP2)
106 0x006A 0 Duration automatic blow
Permissable evacuation time
107 0x006B 0
108 0x006C 0 Permissable leakage rate
119 0x0077 0 Profile name

Production Setup - Profile P1 Ejector 1
180 0x00B4 0 Air-Saving function
Disable continous sucking
181 0x00B5 0
5, 129, 131,
1 byte 165, 167, wo
168, 169
1 byte 0-255 rw
2 bytes 0-999 ro
1 byte 0-2 rw
1 byte 0-2 rw
2 bytes 0-999 rw
2 bytes 0-999 rw
1 byte 0-2 rw
1 byte 0-1 rw
999 > SP1
2 bytes rw
> rP1
SP1 > rP1 >
2 bytes rw
SP2
rP1 > SP2 >
2 bytes rw
rP2
SP2 > rP2
2 bytes rw
>= 10
2 bytes 100-9999 rw
2 bytes 0-9999 rw
2 bytes 0-999 rw
0...16 bytes - rw
1 byte 0-2 rw
1 byte 0-1 rw
0x81 (dec 129): Reset application
0x83 (dec 131): Back to box (IO-Link-Communciation will be stopped, restart by
power cycle is needed)
- 0xA5 (dec 165): Calibrate all vacuum sensor
0xA7 (dec 167): Reset erasable counters
0xA8 (dec 168): Reset voltages min/max
0xA9 (dec 169): Reset vacuum min/max
Bit 0: NFC write lock
Bit 1: NFC disable
Bit 2: Not used
0
Bit 3: reserved
Bit 4: IO-Link event lock (suppress sending IO-Link events)
Bit 5-7: Not used
0 Pin-Code for NFC write
0 = Externally controlled drop-off
0 1 = Internally controlled drop-off – time-dependent
2 = Externally controlled drop-off – time-dependent
0 = Externally controlled drop-off
0 1 = Internally controlled drop-off – time-dependent
2 = Externally controlled drop-off – time-dependent
10 Unit: 1ms
10 Unit: 1ms
0 = not active (off)
1 1 = active (on)
2 = active with supervision (onS)
0 = off,
0
1 = on
750 Unit: 1mbar
600 Unit: 1mbar
550 Unit: 1mbar
540 Unit: 1mbar
200 Unit: 1ms
Unit: 1ms
2000
no evacuation time warning if set to 0
Unit: 1mbar/s
250
no leakage rate warning if set to 0
*** Name of profile
0 = not active (off)
0 1 = active (on)
2 = active with supervision (onS)
0 = off,
0
1 = on