Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Never leave the running machine unattended. Switch off the machine before leaving the
•
working area and secure it against unintentional or unauthorized restarting.
The machine may only be operated, maintained or repaired by persons who are familiar and
•
who have been informed about the dangers arising from this work.
Ensure that unauthorized persons keep a safety distance from the machine and keep children
•
away from the machine.
•
Hide long hair under hair protection.
Wear close fitting protective work clothing and suitable protective equipment (eye protection,
•
dust mask, ear protection and work gloves only when handling tools).
•
Never wear loose jewellery, loose clothing or accessories (e.g. tie, scarf).
•
Always work with care and the necessary caution and never use excessive force.
Do not remove any sections or other parts of the workpiece from the cutting area while the
•
machine is running!
Do not overload the machine!
•
Do not work on the machine if you are tired, not concentrated or under the influence of
•
medication, alcohol or drugs!
Do not use the machine in areas where vapours of paints, solvents or flammable liquids
•
represent a potential danger (danger of fire or explosion!).
•
Do not smoke in the immediate vicinity of the machine (fire hazard)!
•
Shut down the machine and disconnect it from the power supply, before adjustment,
changeover, cleaning, maintenance or repair work, etc. Before starting work on the machine,
wait until all tools or machine parts have come to a complete standstill and secure the machine
against unintentional restart.
Warning signs and/or stickers on the machine that are illegible or have been removed must be
•
replaced immediately!
12.5
Electrical safety
Only use suitable extension cables
•
A damaged or tangled cable increases the risk of electric shock. Handle the cable with care.
•
Never use the cable to carry, pull or disconnect the power tool. Keep the cable away from heat,
oil, sharp edges or moving parts.
Proper plugs and outlets reduce the risk of electric shock.
•
Water entry into the machine increases the risk of electric shock. Do not expose the machine to
•
rain or moisture.
•
The machine may only be used if the power supply is protected by a residual current circuit
breaker.
•
Use the machine only when the ON-OFF switch is in good working order.
•
Before connecting the machine always make sure that it is switches off.
Avoid contact of the body with grounded surfaces such as pipes, radiators, ovens and
•
refrigerators. There is an increased risk of electric shock if the body is earthed.
12.6
Special safety instructions for this machine
•
During operation of the machine wood dust is generated. Therefore, connect the machine to a
suitable dust collection system for dust and chips during installation!
•
Always switch on the dust collection system before you start machining the workpiece!
•
Never remove sections or other parts of the workpiece from the cutting area while the machine
is running.
•
When using milling tools with a diameter of ≥ 16 mm and circular saw blades, these must
comply with EN 847-1:2013 and EN 847-2:2013; tool carriers must comply with EN 847-3:2013;
•
Excessive noise can cause hearing damage and temporary or permanent hearing loss. Wear
hearing protection certified to health and safety regulations to limit noise exposure.
Replace cracked and deformed saw blades immediately, they cannot be repaired.
•
•
Use clean and sharpened saw blades, which are less sensitive to malfunctions and easier to
guide.
If possible, use clamps to hold/fix the workpiece. If you hold the workpiece by hand, always hold
•
your hand at least 100 mm from both sides of the saw blade. Do not use this saw to cut parts
that are too small to be securely clamped or held by hand.
Never cross the intended cutting line in front of or behind the saw blade.
•
Check your workpiece before cutting. If the workpiece is bent or warped, clamp it with the
•
outside bent surface against the stop. Always make sure that there is no gap between the
workpiece, stop and table along the cutting line. Bent or warped workpieces can twist or move
ZIPPER MASCHINEN GmbH
www.zipper-maschinen.at
(cross-section 1.5mm² for length up to 25m; H05VV-F)
SAFETY
.
31
ZI-KGS210DS
Publicité
Table des Matières
