Sauder Palladia Serie Mode D'emploi
Masquer les pouces Voir aussi pour Palladia Serie:

Publicité

Liens rapides

sauder.com
L-Shaped Desk
Palladia Collection | Model 417714
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
The original desktop.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-64
Français pg 65-72
Español pg 73-80
Lot # 511553
12/15/17
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987

Publicité

Table des Matières
loading

Sommaire des Matières pour Sauder Palladia Serie

  • Page 1 Palladia Collection | Model 417714 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Prefer the phone? Call 1-800-523-3987.
  • Page 2 TOP RIGHT REAR MOLDING (1) RIGHT MODESTY PANEL (1) LEFT BACK SKIRT (2) PLINTH (8) LEFT MODESTY PANEL (1) KEYBOARD UPRIGHT (1) MMM HALF DISK (8) SPACER (2) KEYBOARD FRONT (1) END MOLDING (4) KEYBOARD BACK (1) Page 2 417714 www.sauder.com/services...
  • Page 3: Part Identifi Cation

    Now you know Part Identifi cation our ABCs. www.sauder.com/services 417714 Page 3...
  • Page 4 RIGHT DRAWER SIDE (Top Left) (1) D708 FILE DRAWER BOTTOM (1) TOP RIGHT DRAWER BACK (1) LEFT DRAWER SIDE (Top Left) (1) DRAWER BOX FRONT (1) RIGHT DRAWER SIDE (Top Right) (1) D716 DRAWER BOTTOM (2) D958 D716 D211 D708 D716 Page 4 417714 www.sauder.com/services...
  • Page 5 KNOB - 6 FELT DISC CARD - 1 LOCK - 1 LOCK COVER - 1 BRACKET - 1 GROMMET - 3 METAL PIN - 8 RUBBER SLEEVE - 4 GROMMET CAP - 3 CORD CLIP - 3 www.sauder.com/services 417714 Page 5...
  • Page 6: Table Des Matières

    52S SILVER 3/4" PAN HEAD SCREW - 2 GOLD 1" MACHINE SCREW - 1 SILVER 9/16" LARGE HEAD SCREW - 2 SMALL BLACK 1-1/4" FLAT HEAD SCREW - 2 113S BLACK 1-15/16" FLAT HEAD SCREW - 12 Page 6 417714 www.sauder.com/services...
  • Page 7 Look for this icon. It means a Step 1 video assembly tip is available at www.sauder.com/services/tips Assemble your unit on a carpeted fl oor or on the empty å KEYBOARD DRAWER ON RIGHT VIDEO carton to avoid scratching your unit or the fl oor.
  • Page 8 Fasten the KEYBOARD HINGES (12H) to the å KEYBOARD SHELF (AAA). Use two SILVER 9/16" LARGE HEAD SCREWS (54S). SILVER 5/8" FLAT HEAD SCREW SILVER 9/16" LARGE HEAD SCREW (4 used in this step) (2 used in this step) Page 8 417714 www.sauder.com/services...
  • Page 9: Gold 5/16" Flat Head Screw

    BROWN 1-1/2" FLAT HEAD SCREW (2 used for the #1 holes in the SLIDES) Open end BLACK 7/8" MACHINE SCREW (1 used for the KNOB) GOLD 5/16" FLAT HEAD SCREW (2 used for the fi rst holes in the SLIDES) www.sauder.com/services 417714 Page 9...
  • Page 10 Be sure the grooves in each part line up with each other on the inside of the drawer. D716 Use top hole Groove D958 Groove BLACK 1-9/16" FLAT HEAD SCREW (12 used in this step) D211 D708 D211 Groove Page 10 417714 www.sauder.com/services...
  • Page 11: Black 9/16" Large Head Screw

    Fasten the TOP DRAWER FRONTS (GG and LL) to the TOP å DRAWER FRONT BRACKETS (6G). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). BLACK 9/16" LARGE HEAD SCREW (4 used in this step) Push down www.sauder.com/services 417714 Page 11...
  • Page 12 Fasten a KNOB (42K) to the TOP LEFT DRAWER FRONT (LL). Use a BLACK 7/8" MACHINE SCREW (37S). å BLACK 1-9/16" FLAT HEAD SCREW (2 used through hole #1) Open end Open end BLACK 7/8" MACHINE SCREW (1 used for the KNOB) GOLD 5/16" FLAT HEAD SCREW (2 used through hole #3) Page 12 417714 www.sauder.com/services...
  • Page 13 Fasten a KNOB (42K) to the TOP RIGHT DRAWER FRONT (GG). Use a BLACK 7/8" MACHINE SCREW (37S). å BLACK 7/8" MACHINE SCREW (1 used for the KNOB) Open end Open end GOLD 5/16" FLAT HEAD SCREW (4 used for the SLIDES) www.sauder.com/services 417714 Page 13...
  • Page 14: Black 1-1/8" Pan Head Screw

    FRONTS (S and Z). Use eight BLACK 1-1/8" PAN HEAD SCREWS (9S). your screwdriver and hammer. Push down D211 These edges should be even. BLACK 1-1/8" PAN HEAD SCREW (8 used for the DRAWER FRONTS) These edges should be even. Page 14 417714 www.sauder.com/services...
  • Page 15: Silver 1-1/4" Machine Screw

    BOX FRONT, through the DRAWER FRONT, and into the KNOB. Open end BLACK 1-9/16" FLAT HEAD SCREW (2 used through hole #1) Open end SILVER 1-1/4" MACHINE SCREW (1 used for the KNOB) GOLD 5/16" FLAT HEAD SCREW (2 used through hole #3) www.sauder.com/services 417714 Page 15...
  • Page 16 Push the black lever in and pull the SLIDE from the RAIL. Open end SILVER 1-1/4" MACHINE SCREW (1 used for the KNOB) D211 Open end GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Page 16 417714 www.sauder.com/services...
  • Page 17 Fasten the LOCK BRACKET (5J) to the FILE DRAWER RIGHT SIDE (D211). Use a BROWN 7/16" LARGE HEAD SCREW (6S). å Insert the FILE RODS into the holes of your choice in the FILE GLIDES, depending on your fi le sizes. D211 BROWN 7/16" LARGE HEAD SCREW (1 used in this step) www.sauder.com/services 417714 Page 17...
  • Page 18 Step 12 Fasten the HINGES (14H) to the DOOR (P). Use four å BLACK 1/2" FLAT HEAD SCREWS (11S). BLACK 1/2" FLAT HEAD SCREW (4 used in this step) Page 18 417714 www.sauder.com/services...
  • Page 19 Step 13 Push four SAUDER TWIST-LOCK® FASTENERS (7F) into the large holes in the å OUTER ENDS (A and C). Repeat this step for the INNER ENDS (B3 and D3), BOTTOMS (I2 and J2), å RIGHT MODESTY PANEL (K2), BACKS (N and O), LEGS (R and T), KEYBOARD UPRIGHT (VV), and both SPACERS (L4).
  • Page 20 Open end GOLD 5/16" FLAT HEAD SCREW (12 used in this step) Open end Open end Open end When this NARROW EXTENSION RAIL (40NA) is fastened to the UPRIGHT (E2), it will hang over the edge. Page 20 417714 www.sauder.com/services...
  • Page 21 RAIL out to fi nd the other holes that line up with the holes in the END and UPRIGHT. Turn a SCREW into this hole. GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Open end Open end www.sauder.com/services 417714 Page 21...
  • Page 22 Fasten the HALF DISKS (MMM) to the PLINTHS (JJJ). Use å eight BROWN 1" FLAT HEAD SCREWS (12S). Remember: Righty tighty. Lefty loosey. BROWN 1" FLAT HEAD SCREW (8 used in this step) The larger hole should be facing up. Page 22 417714 www.sauder.com/services...
  • Page 23 Fasten four PLINTHS (JJJ) to the OUTER ENDS (A and C). å Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). (28 used) BLACK 9/16" LARGE HEAD SCREW (36 used in this step) Use bottom holes Use bottom holes www.sauder.com/services 417714 Page 23...
  • Page 24 HALF DISKS (MMM) on the PLINTHS (JJJ). BLACK 9/16" LARGE HEAD SCREW (20 used in this step) Use bottom holes Use bottom holes The END MOLDINGS (M35) should be centered over the HALF DISKS (MMM). Page 24 417714 www.sauder.com/services...
  • Page 25 PANEL (QQ). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. Arrow Arrow Insert the metal end of the CAM DOWEL into the HIDDEN CAM. www.sauder.com/services 417714 Page 25...
  • Page 26 Tap fi ve MOLDING CONNECTORS (17F) into the notches in å the MOLDINGS (BBB, CCC, DDD, EEE, FFF, GGG, and HHH). Use your hammer to tap the MOLDING CONNECTORS (17F) into the notches in the MOLDINGS. Flat end Flat end Flat end Page 26 417714 www.sauder.com/services...
  • Page 27 NOTE: Do not overtighten the SCREWS into the TOP. å The large hole must be here. BLACK 1-1/4" FLAT HEAD SCREW (26 used in this step) Do not overtighten the SCREWS (7S). The large hole must be here. www.sauder.com/services 417714 Page 27...
  • Page 28 SIDE MOLDING (FFF) on the RIGHT TOP (G2). Tighten two TWIST-LOCK® FASTENERS. Fasten a SPACER (L4) to the OUTER RIGHT END (A). å How to use the SAUDER TWIST-LOCK ® FASTENER Tighten two TWIST-LOCK® FASTENERS. 1. Insert the dowel end of the FASTENER into the hole of the adjoining part.
  • Page 29 BLACK 1-15/16" FLAT HEAD SCREW (2 used in this step) ® i t h f a c - L O S u r I S T r f a I S T w i t - L O ® www.sauder.com/services 417714 Page 29...
  • Page 30 Fasten a SPACER (L4) to the OUTER LEFT END (C). å Tighten two TWIST-LOCK® FASTENERS. Surface with TWIST-LOCK® FASTENERS r f a I S T w i t - L O ® Large hole should be located here. Page 30 417714 www.sauder.com/services...
  • Page 31 BLACK 1-15/16" FLAT HEAD SCREW (2 used in this step) w i t ® r f a - L O I S T r f a I S T w i t - L O ® www.sauder.com/services 417714 Page 31...
  • Page 32 Keyboard Drawer on the right side of your Desk. KEYBOARD DRAWER ON RIGHT KEYBOARD DRAWER Follow steps 43-58 as shown below if you prefer the å Keyboard Drawer on the left side of your Desk. KEYBOARD DRAWER ON LEFT KEYBOARD DRAWER Page 32 417714 www.sauder.com/services...
  • Page 33 Pull at the front and back edges, slowly working the FASTENERS out of the holes. Push the LEFT UPRIGHT (F2) onto the TWIST-LOCK® å FASTENERS (7F) in the LEFT TOP (H2) and LEFT BACK (O). Tighten four TWIST-LOCK® FASTENERS. These edges should be even. www.sauder.com/services 417714 Page 33...
  • Page 34: Black 1-15/16" Flat Head Screw

    Push two CORD CLIPS (9P) into the holes in the LEFT TOP (H2). å NOTE: The CORD CLIPS are used to manage your cords. å 113S BLACK 1-15/16" FLAT HEAD SCREW (2 used in this step) BLACK 9/16" LARGE HEAD SCREW (4 used for the CONNECTOR PLATE) Page 34 417714 www.sauder.com/services...
  • Page 35 F A S I S T - L O C E R S T E N T E N ® E R S F A S BLACK 1-1/8" PAN HEAD SCREW (2 used in this step) www.sauder.com/services 417714 Page 35...
  • Page 36 BOTTOM (J2). Use fi ve BLACK 9/16" LARGE HEAD SCREWS (1S) through the holes in the BRACKETS and into the holes in the LEFT BOTTOM. These edges should be even. BLACK 9/16" LARGE HEAD SCREW (14 used in this step) Page 36 417714 www.sauder.com/services...
  • Page 37 Fasten the LEFT BACK SKIRTS (UU) to the å INNER LEFT END (D3), LEFT BOTTOM (J2), and LEFT SIDE SKIRT (SS). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). BLACK 9/16" LARGE HEAD SCREW (16 used in this step) www.sauder.com/services 417714 Page 37...
  • Page 38 EXTENSION RAIL in to fi nd the other hole that lines up with the holes in the UPRIGHTS. Turn a SCREW into this hole. Open end Open end Surface with TWIST-LOCK® FASTENERS Finished edge GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Page 38 417714 www.sauder.com/services...
  • Page 39 Tighten Risk of damage or Arrow injury. HIDDEN CAMS must be completely Arrow Maximum tightened. HIDDEN 210 degrees CAMS that are not completely tightened may loosen, and parts may separate. To Minimum completely tighten: 190 degrees www.sauder.com/services 417714 Page 39...
  • Page 40 FASTENERS (7F) in the RIGHT TOP (G2) and RIGHT BACK (N). Tighten four TWIST-LOCK® FASTENERS. Large hole should be located here. i t h o f a c I O N S u r E N S E X T Page 40 417714 www.sauder.com/services...
  • Page 41 å NOTE: The CORD CLIP is used to manage your cords. å 113S BLACK 1-15/16" FLAT HEAD SCREW (2 used in this step) r f a I S T w i t - L O ® www.sauder.com/services 417714 Page 41...
  • Page 42 BRACKETS and into the holes in the RIGHT BOTTOM. Surface with TWIST-LOCK® FASTENERS BLACK 9/16" LARGE HEAD SCREW (4 used for the CORNER BRACKETS) 113S BLACK 1-15/16" FLAT HEAD SCREW (2 used in this step) Page 42 417714 www.sauder.com/services...
  • Page 43 SKIRT (RR). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). Insert a GROMMET (10P) and GROMMET CAP (1P) into å the large hole in the RIGHT UPRIGHT (E2). BLACK 9/16" LARGE HEAD SCREW (8 used in this step) www.sauder.com/services 417714 Page 43...
  • Page 44 Fasten the RIGHT LEG (R) to the RIGHT MODESTY å PANEL (K2). Use two BLACK 1-1/8" PAN HEAD SCREWS (9S). BLACK 1-1/8" PAN HEAD SCREW (2 used in this step) BLACK 9/16" LARGE HEAD SCREW (4 used for the CONNECTOR PLATE) Page 44 417714 www.sauder.com/services...
  • Page 45 DOOR where it comes in contact with the RIGHT UPRIGHT (E2). Mounting Fasten a KNOB (42K) to the DOOR (P). Use a GOLD 1" MACHINE å screw SCREW (50S). Hinge GOLD 1" MACHINE SCREW (1 used for the KNOB) www.sauder.com/services 417714 Page 45...
  • Page 46 Tighten the screws after making adjustments. To adjust the DOOR in or out (depth), loosen å the mounting screw one turn and move the DOOR in or out, as needed. Tighten the (vertical adjustment) mounting screw after making adjustments. Page 46 417714 www.sauder.com/services...
  • Page 47: Silver 3/4" Pan Head Screw

    Fasten the LOCK (1J) to the LEFT UPRIGHT (F2). Use two å KEYBOARD DRAWER SILVER 3/4" PAN HEAD SCREWS (52S). ON RIGHT Push the LOCK COVER (10J) over the LOCK (1J). å SILVER 3/4" PAN HEAD SCREW (2 used in this step) www.sauder.com/services 417714 Page 47...
  • Page 48 Click the inner cartridge into place against the black tab. Front Extension Rail Inner cartridge Black tab 70 lbs. 50 lbs. 20 lbs. 5 lbs. 5 lbs. 20 lbs. 40 lbs. 35 lbs. 25 lbs. (4 used) Page 48 417714 www.sauder.com/services...
  • Page 49 EXTENSION RAIL in to fi nd the other hole that lines up with the holes in the UPRIGHTS. Turn a SCREW into this hole. Open end Finished edge Surface without TWIST-LOCK® Open end FASTENERS GOLD 5/16" FLAT HEAD SCREW (4 used in this step) www.sauder.com/services 417714 Page 49...
  • Page 50 Push the LEFT UPRIGHT (F2) onto the TWIST-LOCK® FASTENERS (7F) å in the LEFT TOP (H2) and LEFT BACK (O). Tighten four TWIST-LOCK® FASTENERS. 113S BLACK 1-15/16" FLAT HEAD SCREW (2 used in this step) These edges should be even. Page 50 417714 www.sauder.com/services...
  • Page 51 Push two CORD CLIPS (9P) into the holes in the LEFT TOP (H2). å NOTE: The CORD CLIPS are used to manage your cords. å 113S BLACK 1-15/16" FLAT HEAD SCREW (2 used in this step) BLACK 9/16" LARGE HEAD SCREW (4 used for the CONNECTOR PLATE) www.sauder.com/services 417714 Page 51...
  • Page 52 F A S I S T - L O C E R S T E N T E N ® E R S F A S BLACK 1-1/8" PAN HEAD SCREW (2 used in this step) Page 52 417714 www.sauder.com/services...
  • Page 53 BOTTOM (J2). Use fi ve BLACK 9/16" LARGE HEAD SCREWS (1S) through the holes in the BRACKETS and into the holes in the LEFT BOTTOM. These edges should be even. BLACK 9/16" LARGE HEAD SCREW (14 used in this step) www.sauder.com/services 417714 Page 53...
  • Page 54 Fasten the LEFT BACK SKIRTS (UU) to the å INNER LEFT END (D3), LEFT BOTTOM (J2), and LEFT SIDE SKIRT (SS). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). BLACK 9/16" LARGE HEAD SCREW (16 used in this step) Page 54 417714 www.sauder.com/services...
  • Page 55 FASTENERS (7F) in the RIGHT TOP (G2) and RIGHT BACK (N). Tighten four TWIST-LOCK® FASTENERS. Large hole should be located here. i t h o f a c I O N S u r E N S E X T www.sauder.com/services 417714 Page 55...
  • Page 56 å NOTE: The CORD CLIP is used to manage your cords. å 113S BLACK 1-15/16" FLAT HEAD SCREW (2 used in this step) r f a I S T w i t - L O ® Page 56 417714 www.sauder.com/services...
  • Page 57 BRACKETS and into the holes in the RIGHT BOTTOM. Surface with BLACK 9/16" LARGE HEAD SCREW TWIST-LOCK® (4 used for the CORNER BRACKETS) FASTENERS 113S BLACK 1-15/16" FLAT HEAD SCREW (2 used in this step) www.sauder.com/services 417714 Page 57...
  • Page 58 SKIRT (RR). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). Insert a GROMMET (10P) and GROMMET CAP (1P) into å the large hole in the RIGHT UPRIGHT (E2). BLACK 9/16" LARGE HEAD SCREW (8 used in this step) Page 58 417714 www.sauder.com/services...
  • Page 59 Tighten Risk of damage or Arrow injury. HIDDEN CAMS must be completely Arrow Maximum tightened. HIDDEN 210 degrees CAMS that are not completely tightened may loosen, and parts may separate. To Minimum completely tighten: 190 degrees www.sauder.com/services 417714 Page 59...
  • Page 60 å leave without a bite. PANEL (K2). Use two BLACK 1-1/8" PAN HEAD SCREWS (9S). BLACK 1-1/8" PAN HEAD SCREW (2 used in this step) BLACK 9/16" LARGE HEAD SCREW (4 used for the CONNECTOR PLATE) Page 60 417714 www.sauder.com/services...
  • Page 61 DOOR where it comes in contact with the RIGHT UPRIGHT (E2). Mounting Fasten a KNOB (42K) to the DOOR (P). Use a GOLD 1" å screw MACHINE SCREW (50S). Hinge GOLD 1" MACHINE SCREW (1 used for the KNOB) www.sauder.com/services 417714 Page 61...
  • Page 62 Adjusting screw (horizontal) To adjust the DOOR in or out (depth), loosen å the mounting screw one turn and move the DOOR in or out, as needed. Tighten the mounting screw after making adjustments. (vertical adjustment) Page 62 417714 www.sauder.com/services...
  • Page 63 Fasten the LOCK (1J) to the LEFT UPRIGHT (F2). Use two KEYBOARD å SILVER 3/4" PAN HEAD SCREWS (52S). DRAWER ON LEFT Push the LOCK COVER (10J) over the LOCK (1J). å SILVER 3/4" PAN HEAD SCREW (2 used in this step) www.sauder.com/services 417714 Page 63...
  • Page 64 Click the inner cartridge into place against the black tab. DRAWER ON LEFT Front Extension Rail Inner cartridge Black tab 70 lbs. 50 lbs. 20 lbs. 5 lbs. 5 lbs. 20 lbs. 40 lbs. 25 lbs. 35 lbs. (4 used) Page 64 417714 www.sauder.com/services...
  • Page 65: Liste De Pièces

    ARRIÈRE DE TIROIR GAUCHE SUPÉRIEUR ..... 1 MONTANT DROIT ................. 1 CÔTÉ DE TIROIR DROIT (Supérieur gauche) ....1 Pour contacter Sauder MONTANT GAUCHE ................1 CÔTÉ DE TIROIR GAUCHE (Supérieur gauche) ... 1 DESSUS DROIT ..................1 en ce qui concerne cet D716 FOND DE TIROIR ..................2...
  • Page 66 Enfi ler les FONDS DE TIROIR (D708, D716, D958) dans les rainures des CÔTÉS DE TIROIR (D34, D35, D36, D37, D46, D47, D211, D32) et des ARRIÈRES DE TIROIR (D74, D77, D76 et D78). S’ a ssurer d’utiliser les pièces exactes indiquées. Page 66 417714 www.sauder.com/services...
  • Page 67 TABLETTE DE CLAVIER (VV) et les deux ESPACEURS (L4). DE TIROIR, à travers le DEVANT DE TIROIR et dans le BOUTON. REMARQUE : Ne pas insérer une FIXATION TWIST-LOCK® SAUDER dans les MONTANTS (E2 et F2) à ce point. ÉTAPE 10 ÉTAPE 14 Séparer les COULISSES D'EXTENSION LARGES (40MC) des...
  • Page 68 Serrer deux FIXATIONS TWIST-LOCK®. Fixer quatre PLINTHES (JJJ) aux EXTRÉMITÉS EXTERNES (A et C). Utiliser huit VIS TÊTE LARGE 14 mm NOIRES (1S). Utilisation de la FIXATION TWIST-LOCK® SAUDER 1. Insérer l'extrémité fi letée de la FIXATION dans le trou de ÉTAPE 18 la pièce attenante.
  • Page 69 Utiliser deux VIS TÊTE GOUTTE DE SUIF 28 mm NOIRES (9S). Attention Risque des dégâts ou blessures. Les EXCENTRIQUES ESCAMOTABLES doivent être serrés à bloc. Les EXCENTRIQUES ESCAMOTABLES que ne sont pas serrées à bloc peuvent desserrer et les pièces peuvent séparer. www.sauder.com/services 417714 Page 69...
  • Page 70 CÂBLES (1P) dans le gros trou du MONTANT DROIT (E2). après avoir ajusté. ÉTAPE 41 Fixer la SERRURE (1J) au MONTANT GAUCHE (F2). Utiliser deux VIS TÊTE GOUTTE DE SUIF 19 mm ARGENTÉES (52S). Enfoncer le COUVERCLE DE SERRURE (10J) sur la SERRURE (1J). Page 70 417714 www.sauder.com/services...
  • Page 71 Enfoncer le MONTANT DROIT (E2) sur les FIXATIONS TWIST-LOCK® (7F) dans le DESSUS GAUCHE (H2) et l'ARRIÈRE TWIST-LOCK® (7F) dans le DESSUS DROIT (G2) et l'ARRIÈRE GAUCHE (O). Serrer quatre FIXATIONS TWIST-LOCK®. DROIT (N). Serrer quatre FIXATIONS TWIST-LOCK®. www.sauder.com/services 417714 Page 71...
  • Page 72 VIS TÊTE GOUTTE DE SUIF 28 mm NOIRES (9S). sécurité fi gurant sur les pages arrière du manuel d’instructions. Ceci complète l'assemblage. Nettoyer à l’ a ide d’une encaustique pour meubles ou d’un chiff on humide. Essuyer. Page 72 417714 www.sauder.com/services...
  • Page 73: Lista De Partes

    PARAL DERECHO ....................1 40MC CORREDERA DE EXTENSIÓN ANCHA .......2 PARAL IZQUIERDO .....................1 40NA RIEL DE EXTENSIÓN ESTRECHO ...........8 Pour contacter Sauder PANEL SUPERIOR DERECHO ..............1 40NC CORREDERA DE EXTENSIÓN ESTRECHA ......8 en ce qui concerne cet PANEL SUPERIOR IZQUIERDO..............1 CORRIMIENTO DE ARCHIVERO ..........2...
  • Page 74 Fije el POMO (42K) a la CARA DE CAJÓN (BB). Pase un TORNILLO PLATEADO PARA METAL de 32 mm (35S) a través del FRENTE DE CAJÓN, a través de la CARA DE CAJÓN y en el POMO. Page 74 417714 www.sauder.com/services...
  • Page 75 DORSOS (N y O), las PATAS (R y T), el PARAL DE ESTANTE DE sobre los MEDIOS CÍRCULOS (MMM) en las BASES (JJJ). TECLADO (VV) y dos ESPACIADORES (L4). NOTA: No inserte un SUJETADOR TWIST-LOCK® SAUDER en los PASO 19 PARALES (E2 y F2) en este momento.
  • Page 76 Apriete dos SUJETADORES TWIST-LOCK®. derecho o en el lado izquierdo de su Escritorio. Salte los pasos Cómo utilizar el SUJETADOR TWIST-LOCK® SAUDER desde el 27 hasta el 42 para fi jar el Cajón de Teclado al lado derecho de su Escritorio.
  • Page 77 DERECHO INTERIOR (B3), al FONDO DERECHO (I2) y al FALDÓN LATERAL DERECHO (RR). Utilice ocho TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). Inserte un OJAL (10P) y la CUBIERTA DE OJAL (1P) en el agujero grande del PARAL DERECHO (E2). www.sauder.com/services 417714 Page 77...
  • Page 78 SUJETADORES de los agujeros. Tire de los bordes delantero y posterior, CERRADURA (1J). lentamente moviendo los SUJETADORES fuera de los agujeros. Empuje el PARAL IZQUIERDO (F2) sobre los SUJETADORES TWIST- LOCK® (7F) del PANEL SUPERIOR IZQUIERDO (H2) y del DORSO IZQUIERDO (O). Apriete cuatro SUJETADORES TWIST-LOCK®. Page 78 417714 www.sauder.com/services...
  • Page 79 FALDONES POSTERIORES. Fije los FALDONES POSTERIORES IZQUIERDOS (UU) al EXTREMO IZQUIERDO INTERIOR (D3), al FONDO IZQUIERDO (J2) y al FALDÓN LATERAL IZQUIERDO (SS). Utilice ocho TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). www.sauder.com/services 417714 Page 79...
  • Page 80 NOTA: Por favor, lea las páginas de atrás del folleto de instrucciones en cuanto a importante información de seguridad. Esto completa el ensamblaje. Limpie con su pulimento para muebles preferido o un paño húmedo. Seque con un paño. Page 80 417714 www.sauder.com/services...
  • Page 81 à Les téléviseurs peuvent être particulièrement un téléviseur. cet eff et. lourds. De plus, le poids et l’emplacement du tube image ont tendance à rendre les téléviseurs instables et enclins à tomber vers l’ a vant. www.sauder.com/services 417714 Page 81...
  • Page 82 Además, el peso y la ubicación del tubo de imagen tienden a causar la inestabilidad de televisores y propensa a volcarse hacia adelante. Page 82 417714 www.sauder.com/services...
  • Page 83: Garantie Limitée De 5 Ans

    à compter de la date d'achat la première fois et qui sont signalés à Sauder dans les limites de couverture de la contre tout défaut de matériaux ou de fabrication des composantes de mobilier Sauder.
  • Page 84 Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the Set a world record for speed? purchase and assembly process was a positive experience Feeling good about yourself? and you feel good about the furniture you just built. If you Nice.

Ce manuel est également adapté pour:

Palladia 417714

Table des Matières