SYNQ DMC.2000 Mode D'emploi page 17

ENGLISH
4. LOAD HOTCUES: you can choose if the saved hot cues of a track should be recalled automatically.
 Turn the JOG WHEEL (22) to select one of the 2 possibilities:
o First Ask: when a track contains hot cues, the display asks if you want to load the hot cues
or not. You can reply with the YES/NO buttons (29).
o Autoload: when a track contains hot cues, they will be loaded automatically.
5. CROSS FADER: switches the cross fader of the audio mixer on/off, this has no effect on the MIDI
function of the crossfader.
 Turn the JOG WHEEL (22) to select one of the 2 possibilities:
o On: crossfader (56) is activated, ready to be used.
o Off: if you don't like using the crossfader, use this option.
6. REVERSE CROSS FADER: switches the cross fader of the audio mixer in reverse mode, this has no
effect on the MIDI function of the crossfader.
 Turn the JOG WHEEL (22) to select one of the 2 possibilities:
o On: crossfader (56) is working in reverse mode, channel1 is audible while the crossfader is
in the right position.
o Off: crossfader (56) is working in normal mode, channel2 is audible while the crossfader is
in the right position.
7. DISPLAY TIME: you can select how long a message is shown before the display returns to normal
operation.
 Turn the JOG WHEEL (22) to select the desired value: 0,5sec  12,0sec.
8. SCROLL SPEED: you can select how fast the text scroll on the display.
 Turn the JOG WHEEL (22) to select the desired value: 50  2000ms (50ms=fast/2000ms=slow).
9. Sensitivity: you can change the sensitivity of the tactile jog wheel to optimize the jog wheel performance.
 Turn the JOG WHEEL (22) to select one of the 41 possibilities:
o ADJ. = 0:
o ADJ. = -20:
o ADJ. = +20: highest sensitivity
A. INTENSITY: used to adapt the brightness of the VFD-display.
 Turn the JOG WHEEL (22) to select one of the 4 possibilities.
o ADJ. = 1  4: 1 = low brightness, 4 = high brightness (default)
B. A.CUE Level: the auto cue function detects where the music really starts, this avoids blanks when a track
is not well indexed. You can select one of eight detection level presets:
 Turn the JOG WHEEL (22) to select one of the 8 possibilities.
o ADJ. = -78dB  -36dB: the default setting = -48dB
C. Firmware version / upgrading: use this option to check and/or upgrade the firmware versions.
 Turn the TRACK knob (17) to select the 4 firmware parts:
o CON: xx: shows the version of the control firmware
o DSP: xx: shows the version of the DSP firmware
o Upgrade: blinks when the unit is ready to check if there are new firmware versions
available. See "FIRMWARE UPGRADING" for more information.
D. Load defaults: as you already noted this unit is highly configurable but that means also that you can
mess up a lot of settings as well. If you really messed up things, you can still reload the default setting!
 While "Enter Load" is blinking in the display: press the TRACK knob (17) to load the defaults.
E. Exit & Save: if you want your changes to the setup menu to be permanently saved (also after switching
the unit off) you MUST use this option!
 Press the TRACK knob (17) : the display shows "Saving" and exits the setup menu.
Note: alternatively you can also press the RECORD CUE-button (25) to save settings permanently.
SYNQ
®
 MIDI : use this setting when the DMC2000 is exclusively used to control DJ
software. The mixer of the DJ software will be controlled.
 NO MIDI : use this setting if you want to mix different audio sources (DJ
software, external inputs, internal players) with each other, the levels of all
audio sources can be easily matched using the gain knobs (47).
Note: with this setting the mixer is not sending any MIDI, instead it works as
a normal audio mixer.
neutral setting (default setting, OK in most cases)
lowest sensitivity
15/107
OPERATION MANUAL
DMC2000