Operation Without Dmx Controller; Additional Menu Functions; Specifications - IMG STAGELINE DMX-LED-Scheinwerfer Mode D'emploi

4.3 Operation without DMX controller

The following operating modes are available:
1. Static light: user-defined colour
Select the menu item
radiate light in the colour most recently set via
this menu item (mixed colour from red, green
and blue) .
To set the colour, call up
the submenu items
and (blue) one after another (
= maximum brightness) until you obtain
the desired colour .
2. Static light: preset colour
Select the menu item
radiate light in the colour most recently selected .
To select the colour, call up
one of the 25 colours available .
3. Light program
Select the menu item
most recently selected will start .
To select a program, call up
the desired program from the four submenu
items:
stroboscope in the colour set in
cross-fading between colours
change of colour
sound-activated mode (sound-activated
change of colour)
To set the program, call up the correspond-
ing submenu item and set the desired value
... (slow ... fast speed for
; low ... high sound sensitivity for
Master/slave mode (refer to chapter 3.2.2)
Select the desired operating mode (
) for the master unit only .
On all slave units, select the menu item
(the setting of these menu items is irrelevant
in this case) .

4.4 Additional menu functions

After setting these functions, select the desired
operating mode again .
Temperature-controlled power limitation
The spotlight is equipped with a power limitation .
It will protect the spotlight against overheating
when the internal temperature is too high . When
this function has been activated (
consumption of the LED will be reduced to 50 %
when the temperature reaches 80 °C . The power
consumption will rise to 100 % again when the
temperature has dropped to 58 °C .
14
: The spotlight will
and adjust
(red), (green)
= off,
: The spotlight will
and select
: The light program
and select
, ,
) .
, or
or
), the power
In the 10-channel DMX mode, the function can be
deactivated or activated via channel 10 (
page 13) .
Note: The power limitation function is independent of
the temperature-controlled ventilation system .
LED response time
When has been selected, the LED will imme-
diately respond when the brightness setting has
been changed . To simulate the slow response of a
conventional lamp, select the desired setting from
the four settings
(slowest response) .
In the 10-channel DMX mode, the response
time is adjusted via channel 10 (
Default settings
To reset the menu to the default settings, select
the setting and press ENTER to confirm .
After the reset, the menu item
(setting ) .

5 Specifications

Data protocol: . . . . . . . . . . DMX 512
Number of
DMX channels: . . . . . . . . . 5 or 10 (selectable)
Light source: . . . . . . . . . . . RGB COB LED
Power consumption: . . . . 100 W
Beam angle: . . . . . . . . . . 60°
Stroboscope frequency: . . 20 Hz max .
DMX connections: . . . . . . XLR, 3 poles
Pin configuration: . . . . . . pin 1 = ground
Ambient temperature: . . . 0 – 40 °C
Power supply: . . . . . . . . . . 230 V/ 50 Hz
Power consumption: . . . . . 160 VA
Dimensions (W × H × D): . 150 × 220 × 245 mm
Weight: . . . . . . . . . . . . . . 1 .5 kg
Subject to technical modification .
All rights reserved by MONACOR
& Co. KG. No part of this instruction manual may be repro-
duced in any form or by any means for any commercial use.
table,
☞
(slightly slow response) ...
table, page 13) .
☞
is called up
pin 2 = DMX−
pin 3 = DMX+
(without bracket)
INTERNATIONAL GmbH
®