R&G LP0199BK Instructions page 8

•
Tighten the upper nut (item 20) until there is no movement and then lock in position using
the locking nut (item 21). Finally ensure all bolts are secure.
•
Offer the complete assembly into a position so the main wiring socket can be reconnected
as shown in picture 26.
•
Connect the new licence plate illuminator to the wiring connector (item 6). It is a good
idea to check the operation of all lights at this stage, if the licence plate illuminator fails to
Page | 8
work please swap the bullet connectors and retry.
•
Secure the original wiring loom and the licence plate illuminator wires using the cable
ties (item 18) and self-adhesive cable clips (item 17) as shown in pictures 23, 24 and 25.
•
Refit the cable harness as original and using the cable ties secure all wiring as original.
•
Fit the entire assembly onto the rear wheel hub as original and secure using the original
bolts, please ensure the wiring cannot come into contact with the chain, brake disc or any
moving parts when in operation.
•
Re-fit the licence plate (it may require drilling).
•
IMPORTANT: IF FITTING A FULL-SIZE LICENCE PLATE AND PLACING IT FAR DOWN ON
THE LICENCE PLATE HANGER, THERE IS A SMALL CHANCE OF THE LICENCE PLATE
HITTING THE BACK WHEEL UNDER HEAVY LOAD AND OVER LARGE BUMPS IN THE ROAD.
IT IS YOUR RESPONSIBILITY TO CHECK FOR THIS POSSIBILITY AND TAKE AVOIDING
ACTION. FAILURE TO CHECK THIS COULD RESULT IN SERIOUS INJURY OR DAMAGE.
•
Refit both seats.
•
Depending on local laws, attach enclosed red reflector (item 16) in an appropriate
location.
•
Please test the indicators, rear light and licence plate illuminator before riding.
Digital copies of these instructions are available to download from
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable
skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products
R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good
engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting
its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability
shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect
the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they
were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be
in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the
gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No
returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not
refer to faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
GENERAL TORQUE SETTINGS
M4 BOLT = 8Nm
M5 BOLT = 12Nm
M6 BOLT = 15Nm
M8 BOLT = 20Nm
M10 BOLT = 40Nm
ISSUE 1 04/05/2016 (NSY)
ISSUE 2 05/08/2019 (FB)
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com
8
LP0199
www.rg-racing.com
Email: info@rg-racing.com