Transport (Fig. 1, 2); Maintenance; Storage; Electrical Connection - PrimAster KZS-RI2100 Traduction Des Instructions D'origine

• Important! The cutting angle of the teeth, in other
words the direction of rotation of the saw blade
(7) must coincide with the direction of the arrow
on the housing.
• Move the guide bar into position and tighten the
screw (f) again.
• Before continuing your work make sure that all
safety devices are in good working condition.
• Important! Every time that you change the saw
blade (7), check to see that it spins freely in the
table insert (11) in both perpendicular and 45° an-
gle settings.
• Important! The work to change and align the saw
blade (7) must be carried out correctly.
8.11 Using the laser/LED (Fig. 10, 15)
• To switch on: Move the ON/OFF switch of the la-
ser (35) to the "1" position. A laser line is projected
onto the material you wish to process, providing an
exact guide for the cut.
• To switch off: Move the ON/OFF switch of the la-
ser (35) to the "0" position.
8.12 Adjusting the laser (Fig. 10)
If the laser (34) ceases to indicate the correct cutting
line, you can readjust the laser. To do so, open the
screws (36) and set the laser by moving sideways to
that the laser beam strikes the teeth of the saw blade
(7).

9. Transport (Fig. 1, 2)

• Tighten the set screw (26) in order to lock the ro-
tary table (16)
• Press the machine head (5) downwards and se-
cure with the safety pin (24). The saw is now
locked in its bottom position.
• Fix the saw's drag function with the locking screw
for drag guide (23) in rear position.
• Carry the equipment by the fixed saw table (17).
• When reassembling the equipment proceed as de-
scribed under section 7.1.

10. Maintenance

m Warning! Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
General maintenance measures
Wipe chips and dust off the machine from time to
time using a cloth. In order to extend the service life
of the tool, oil the rotary parts once monthly. Do not
oil the motor.
When cleaning the plastic do not use corrosive prod-
ucts.
Brush inspection
Check the carbon brushes after the first 50 operating
hours with a new machine, or when new brushes have
been fitted. After carrying out the first check, repeat
the check every 10 operating hours.
If the carbon is worn to a length of 6 mm, or if the
spring or contact wire are burned or damaged, it is
necessary to replace both brushes. If the brushes are
found to be usable following removal, it is possible to
reinstall them.
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consuma-
bles.
Wear parts*: Carbon brushes, saw blade, table inserts,
dust collecting bags, V-belts
* Not necessarily included in the scope of delivery!

11. Storage

Store the device and its accessories in a dark, dry and
frost-proof place that is inaccessible to children. The
optimum storage temperature is between 5 and 30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from dust
and moisture.
Store the operating manual with the electrical tool.

12. Electrical connection

The electrical motor installed is connected and
ready for operation. The connection complies
with the applicable VDE and DIN provisions.
The customer's mains connection as well as
the extension cable used must also comply with
these regulations.
• The product meets the requirements of EN 61000-
3-11 and is subject to special connection conditions.
This means that use of the product at any freely se-
lectable connection point is not allowed.
• Given unfavourable conditions in the power supply
the product can cause the voltage to fluctuate tem-
porarily.
• The product is intended solely for use at connection
points that
a) do not exceed a maximum permitted sup-
ply impedance "Z" (Zmax = 0.407
b) have a continuous current-carrying capacity of
the mains of at least 100 A per phase.
• As the user, you are required to ensure, in consulta-
tion with your electric power company if necessary,
that the connection point at which you wish to oper-
ate the product meets one of the two requirements,
a) or b), named above.
Ω), or
GB | 31