Warning Label - BEGLEC SPACE COLOR Mode D'emploi

ENGLISH
LASER SAFETY INSTRUCTIONS:
• According to the EN 60825-1:1994 + A1:2002 + A2:2002 regulations, this laser falls
under the classification 3B. Direct eye exposure can be dangerous.
DANGER: LASER RADIATION !
Avoid direct eye exposure! Laser radiation can cause eye damage
and/or skin damage. All protective measures for a safe operation of
this laser must be applied.
• This product is a so-called show laser, emitting radiation with a wavelength spectrum
between 400 and 700 nm and producing lighting effects for shows.
• Due to the construction of this laser, the beam is moved so fast, that it can only hit the
eye very short. This is why the use of this laser for a Laser-Light-Show can be regarded
as save.
• Never direct the laser beam to people or animals and never leave this device running
unattended.
• This laser may only be used for shows. The operation of a class 3B show laser is only
allowed if the operation is controlled by a skilled and well-trained operator.
• Depending on the classification, operating a laser product can produce laser radiation
that may cause permanent eye damage and/or skin damage. The legal instructions for
using a laser product vary from country to country. The user must always inform himself
on the legal instructions valid in his country and apply them to his situation.
Please note that JB SYSTEMS cannot be made liable for damages caused by incorrect
installations and unskilled operation!
DESCRIPTION:
1. MAINS INPUT: with IEC socket and integrated fuse holder, connect the supplied mains
cable here.
2. ON/OFF KEY ACTUATED SWITCH: used to switch the unit on/off. Use the keys to
make sure only a skilled operator is able to switch the laser on.
3. INTERNAL MICROPHONE: The built-in microphone is used to synchronize the laser
show to the beat of the music.
JB SYSTEMS®
USER MANUAL
3/56 SPACE-COLOR Laser
ENGLISH
4. DMX INPUT: 3pin male XLR-connector used to connect universal DMX-cables. This
input receives instructions from a DMX-controller.
5. DMX OUTPUT: 3pin female XLR-connector used to connect the Space-color laser with
the next unit in the DMX chain.
6. DISPLAY: shows the selected DMX address when the unit is in DMX-mode. Shows 3
horizontal lines when the unit is in stand-alone mode.
7. DIP-SWITCHES: switches 1~8 are used to set the DMX address between 000 and
255. Switch 9 is not used and switch 10 is used to select stand-alone or DMX mode.
8. AUTO/MUSIC SWITCH: when the unit is used in stand-alone mode, this switch sets
the laser in music mode (patterns move to the rhythm of the beat) or auto mode
(patterns move automatically)
9. SAFETY EYE: used to attach a safety cable when the unit is rigged (see paragraph
"overhead rigging"
10. MUSIC INPUT SENSITIVITY: This potentiometer is used to adjust the music input
sensitivity. Turn the potentiometer until the laser works in sync with the music.
11. COOLING FAN: used to cool the components inside the enclosure. Make sure to
never cover this fan outlet!
12. REMOTE CONTROL: ¼" jack used to connect the optional CA-8 controller.
13. POWER LED: indicates that the unit is switched on.
14. SOUND LED: flashes to the sound of the music detected by the internal microphone.
15. HANGING BRACKET: with 2 knobs on both sides to fasten the unit and a mounting
hole to fix a mounting hook.
16. LASER OUTPUT: Here the laser beam leaves the enclosure, make sure to NEVER
look inside the unit through this opening while the laser effect is switched on!
17. WARNING LABEL: "Caution – Class 3B laser. Laser Radiation when open. Avoid
exposure to beam."
18. WARNING LABEL: "Laser Aperture"
19. LASER WARNING SIGN: warns against a potentially dangerous laser when not used
by skilled operators.
20. WARNING LABEL: "Laser Radiation. Avoid exposure to beam. Class 3B laser
product"
JB SYSTEMS®
USER MANUAL
4/56 SPACE-COLOR Laser