Chicco LITEWAY2 Manuel page 12

using the anchorage points. The
harness must be re adjusted. To
make sure the harness straps are
fitted correctly (on the rear surface
of the seat), place the child inside,
fasten the straps and then pull the
ends of the straps firmly.
• Always apply the brakes whenever
the stroller is stopped.
• To avoid all strangulation risks, nev-
er give children objects with cords or
strings attached, or leave them with in
proximity of such objects.
• Always pay attention when going
up and down steps or pavements.
• If the stroller has been exposed di-
rectly to sunlight for a long time,
you must let it cool down before
placing your child inside of it. Pro-
longed exposure to direct sunlight
may cause the colour of the mate-
rials and fabric to fade.
• Do not use this product if some
parts are broken, torn or missing.
• Prevent the stroller from contact
with salty water. It might cause the
formation of rust.
• Do not use the stroller on the
beach.
TIPS FOR CLEANING AND MAINTENANCE
This product requires periodical maintenance. Cleaning
and maintenance operations must be carried out by an
adult.
CLEANING
The cover can be removed (please refer to the section "How
to Remove the Fabric Cover"). Please refer to the care labels
for instructions on how to clean the fabric parts. Below are
the cleaning symbols and their meanings:
Wash by hand in cold water
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean
Periodically wipe clean plastic parts with a soft damp cloth.
Always dry the metal parts to prevent the formation of rust
if the folding cot has come into contact with water.
MAINTENANCE
Lubricate the moving parts only if necessary, with a light
application of a silicone based lubricant. Regularly check
the condition of the wheels and, keep them clean of dust
and sand. To avoid friction that may prevent correct oper-
ation of the stroller, make sure that all the movable plastic
parts along the metal frame are clean of dust, dirt or sand.
Keep the stroller in a dry place.
GENERAL INSTRUCTIONS
HOW TO ASSEMBLE THE FRONT WHEELS
1.Assemble the front wheel, inserting it into the appropri-
ate joint. A click will be heard, indicating that it is locked
correctly into position (fig. 1). Repeat this operation with
the other wheel.
WARNING: Before use, ensure that the wheels are locked
correctly.
HOW TO OPEN THE STROLLER
WARNING: When opening the stroller, make sure that your
child or other children are at a safety distance.
Make sure that during these operations the moving parts
of the stroller will not come into contact with your child
2. Release the closing device and push the front part of the
stroller forward (fig. 2).
3. Push the rear primary locking mechanism downward with your
foot (fig. 3).
WARNING: Before use, ensure that the stroller is locked in
the open position, by checking that the rear locking mech-
anism is effectively locked.
HOW TO USE THE SAFETY HARNESS
This stroller has a five-point safety harness featuring two
shoulder straps, two adjustment holes, a waist strap and a
crotch strap with buckle.
After removal of the safety harness (e.g. for washing), en-
sure that the harness is reassembled correctly using the
anchorage points. The harness must be re adjusted.
WARNING: When carrying children up to 6 months of age,
the shoulder straps must be passed through the 2 adjuster
slots.
4. If necessary, adjust the height of the shoulder straps, in-
serting them into the adjustment hole, as shown in fig. 4.
After sitting your child in the stroller, fasten the safety har-
ness, first inserting the two prongs into the hole located
on the shoulder straps (fig. 4A and 4B) and then into the
buckle of the crotch strap (fig. 4C). Adjust the length of the
straps, ensuring that they adhere to the child's shoulders
and body correctly. To unfasten the waist strap, press and
pull the side prongs.
WARNING: Children must wear all the time the safety har-
ness. To ensure your child's safety, it is necessary to always
use the safety harness.
HOW TO ADJUST THE BACKREST
The backrest can be adjusted to 5 positions.
5. Fit the two fabric panels to the rear tubes by fastening
the two press studs, as shown in Fig. 5.
6. To adjust the inclination of the backrest, press the but-
12