stayer SCR 216 W Instructions D'emploi page 20

Adjusting the angle for vertical cut at 45° (bevel)
Verification
1 Release the vertical adjustment of the head by loosening
the head angle control lever (5). Remove the extendible
lateral support guide by loosening the knob (17) before
you can tilt the machine head.
2 Tilt the head as far right as possible (45°). On the
SCR315W model, the head can tilt to both sides. To tilt
the head all the way to the left, pull the pin (18).
3 Check the angle using a duly calibrated angle chart or
goniometer (minimum accuracy +/- 5°), placing one side
on the cutting table and the other side on the cutting
blade.
4 If the face of the angle chart does not fit the blade exactly
or if there is a deviation greater than +/- 20° when using
the goniometer, an adjustment must be made.
Adjustment
1 Using a goniometer (minimum accuracy +/- 5°), place
one side on the cutting table and the other side on the
cutting blade.
2 Adjust the screws located on the head tilt axis (B) until
you reach a measurement of 90° / 45°.
CHANGING TOOLS
8.
Attention!
This operation must be carried out with the machine
unplugged and with the disk still. Use protective gloves.
- Use obligatorily disk according to normative EN 847-1
- Use obligatorily the regulatory push stick and save it away
if not use it.
- Use of fast steel disks prohibited (HSS)
- Use of defective or deformed prohibited
- Replace the table insert when worn
Removing the cutting blade
1 Lock the head in the up position.
2 Detach the blade guard by pulling upwards.
3 On the SCR216W and SCR255CW models, you must
remove the blade guard before you can access the blade.
To remove the guard, unscrew the 3 screws (12). To do
so, set the guard in such a way that the screws become
accessible.4.
4 Press the blade locking knob (7) and carefully turn the
blade until it locks.
5
Remove the blade to be replaced by turning the screw
clockwise.
Changing the cutting blade
1
Carefully clean all sawdust and dirt from the brackets,
flanges and inside of the guards.
2
Place the new cutting blade so that the direction of
the arrow on the front of the casing matches the arrow
engraved on the blade and the tilt of the blade's teeth.
3
Attach the flange and its screw
4
Tighten the screw counter-clockwise. On the SCR216W
and SCR255CW models, the blade guard must be put
back in place by replacing the screws (12) and tightening
them completely.
5 Place the blade guard in its original protective position by
pulling downwards. The blade guard should return to its
original position automatically when released.
6 Check the correct operation by simulating a cutting
operation at idle speed.
FIXING FOR OPERATION
9.
Whenever possible, the workpiece must be fixed in such a
manner that the hand does not intervene.
During the cut, keep the workpiece fixed to the support. ALL
MACHINES ARE PREPARED FOR MOUNTING CLAMPS
ENGLISH
20
ALLOWING FASTENING THE PROFILE IN A SAFE
MANNER.
To avoid deformations of the workpieces during fixing thereof,
the use of wooden profiles being easily applicable to the
movable jaws of the clamps is advised. Clamps can be easily
extracted and leave the working surface totally clear.
For cutting long workpieces under safe conditions it is
essential to hold them with additional supports.
LIMITS REGARDING THE WORKPIECE SIZE
10.
Limits for all models as included in the present manual on
page 3.
GENERAL INSTRUCTIONS FOR USE
11.
Warning!
1
Do NOT use the machine if it is in a bad condition or
lacks parts including the prescribed upper guards (the
illustrations of the present manual may be used as an
orientative guide). Unplug it, remove it from the working
area and immediately send it to an authorized technical
service.
2
Know and comply with all safety measures before you
start the machine.
- Obligatory used of aspiration particle system when cutting
the wood.
Starting and stopping the machine
Information
The machine is equipped with a safety system to prevent
accidental start-up.
On the SCR216W and SCR315W models, if the locking
button (3) is not pressed beforehand, the machine will not
work even when pressing the start-up button (6). This allows
you to lower the head while the machine remains off.
On the SCR255CW model, you can start-up the machine at
any time, but it is impossible to lower the head and expose
the blade without first pulling the locking plate (3).
Warnings!
1 Never leave running machine unattended.
2 Never start the machine with locked disk and, before
starting a cut, always wait until the cutting disk has
reached its maximum speed.
3 Before stopping the machine the disk must be clear and
be rotating freely.
Starting with the manual switch
1 On the SCR216W AND SCR315W models, press the
locking button (3)
2 Press switch 6 on the handle to start the motor
Stopping the machine
1
Stop pushing switch 6.
Preparation and types of cuts
Warning!
It is mandatory to carry out any settings with the cable
unplugged.
Warning!
1
Respect the limits regarding the size and material of the
workpiece.
2
Use clamps to fasten the workpiece whenever possible.
Preparing the cut
To find the desired angle follow the steps: to adjust its position.
20