Table des Matières
Publicité
- WARNING! This barbecue will become very hot.
- WARNING! Keep children and animals away.
- WARNING! Do not stand or sit on worktop
- ALWAYS USE OVEN GLOVES AND HOLDING PADS.
- The wooden, cardboard and plastic parts of the packaging
must be recycled to the local recycling centers
- During winter season we suggest to protect the structure with
our polypropylene cover (optional) in order to avoid water
infiltrations, which may damage the structure.
3 ASSEMBLY
3.1 UNPAINTED REFRACTORY CONCRETE BARBECUE
We suggest you to use Assembly kit Palazzetti (optional)
Assemble the base and worktop of barbecue elements with
mortar (included into Assembly Kit Palazzetti) and check each
step with a spirit level. –Small thickness differences are due to
the material cannot be considered a warranty claim and have to
be leveled with mortar while assembly.
Do not use high resistance cement or quick-setting cement
(white cement, aluminated cement, etc.) or strong glue for tiles
etc. as they prevent the thermal expansion of parts in contact
with heat, causing cracks.
The part in contact with heat (from hearth up) have to be
assemble with glue Easy fix (included into Assembly kit
Palazzetti): This special glue is specific for outdoor and it is
resistant to heat, it become flexible and allow the expansion of
material due to heat of combustion.
Warning: if the fireplace comes in more elements, fit the grill
between the 2 side elements before fixing them. Wait for it to
harden before proceeding;
Place fireplace plates in hearth without fix;
Before using the barbecue, wait for it to dry completely (at least
4 days); Barbecues made of refractory concrete has to be
protected against bad weather by painting it with an outdoor
plastic quartz paint (included into Assembly kit Palazzetti). Are
necessary at least 2 hands, to obtain 2-3 mm thickness. All parts
in Marmotech or already colored in mixture have to be protected
with water repellent treatment Palazzetti (included into
Assembly kit Palazzetti); Repeat it once a year.
3.2 MARMOTECH OR ALREADY COLORED IN MIXTURE
BARBECUE
to assemble the elements only use the special glue for assembly
by Palazzetti (included in some models). This special glue
becomes flexible when heating and can be used to assembly all
the elements of the barbecue.
Assemble the elements in numerical order as shown on the
assembly drawing and check each step with a spirit level. These
kind of models do not require any finishing, but we suggest you
to apply water-repellent treatment Palazzetti, which protects
structure against bad weather and cooking grease. (Included in
some barbecues, to protect only worktop). Repeat it once a
year.
Any imperfections you could find on Easy Stone parts have to
be considered a quality, because these parts are hand made by
expert manufacturer.
3.3 SPECIFIC INSTRUCTIONS TO ASSEMBLE BBQ WITH
OVEN
ONLY FOR GARGANO 3 WITH OVEN
Prepare elements (6-8d-8c-12) for assembly, revise holes for
elements 13.
Lay on worktop (2) fiber ceramic papers (included) without any
glue, and on them lay oven elements (6-8d-8c-9a-10a-11a-12-
12d) respecting all distances as in cutsight without fixing them.
Oven elements (3-4a-4b) have some grooves, assemble fiber
ceramic lanyard using few drop of glue (included). Now you can
unite all oven parts using elements (13). When oven is hot,
elements 13 expands, when it happens do not tight more
(to avoid cracks on elements)
To build cast iron door (optional) use the screw with brass fisher
and use a bit of glue (included) between cast iron frame and
front side of oven (12).
ONLY FOR ANTILLE
Prepare elements (23a-26a-26b-29a) for assembly, revise holes
for elements 33
Lay on worktop (piece 2) fiber ceramic papers (included)
without any glue, and on them lay oven elements (23a-26a-
26b-27a-29a-29b-30a-31a) respecting all distances as in
cutsight without fixing them.
Oven elements (23a-26a-26b) have some grooves, assemble
fiber ceramic lanyard using few drop of glue (included). Now you
can unite all oven parts using elements 33a-33c-33d. When
oven is hot, elements 33a-33c-33d expands, when it
happens do not tight more (to avoid cracks on elements)
To build cast iron door (optional) use the screw with brass fisher
and use a bit of glue (included) between cast iron frame and
front side of oven (29a).
ONLY FOR MAXIME 3 WITH OVEN
Prepare elements 3-4 a-4b-7 for assembly, revise holes for
elements 9
Lay on worktop (piece 2) fiber ceramic papers (included)
without any glue, and on them lay oven elements (3-4 a-4b-5-
6 a-6b-7-8) respecting all distances as in cutsight without fixing
them.
Oven elements (3-4a-4b) have some grooves, assemble fiber
ceramic lanyard using few drop of glue (included). Now you can
unite all oven parts using elements 9-9a-9b. When oven is hot,
7
Publicité
Table des Matières
