Nice AVIO500 Instructions Et Avertissements Pour L'installation Et L'utilisation page 48

STEP 7
This user guide should be stored and handed to all users of the
automation.
7.1 – WARNINGS
• Keep at a safe distance from the moving door until it is com-
pletely open or closed; do not transit through the door until it is
completely open and has come to a standstill.
• Do not let children play near the door or with its commands.
• Keep the transmitters away from children.
• Suspend the use of the automation immediately as soon as you
notice something abnormal in the operation (noises or olting
movements); failure to follow this warning may cause serious
danger and accidents.
• Do not touch moving parts.
• Regular maintenance checks must be carried out by qualified
personnel according to the maintenance plan.
• Maintenance or repairs must only be carried out by qualified
technical personnel.
• Send a command with the safety devices disabled:
If the safety devices do not work properly or are out of order, the door can
still be operated.
01. Command the door with the transmitter. If the safety devices give the
enable signal, the door opens normally; otherwise, reattempt within 3
seconds and keep the control activated.
02. After approximately 2 seconds the door will start moving in the "man
present" mode, that is, so long as the control is kept activated the
door will keep moving; as soon as the control is released the door will
stop.
If the safety devices are out of order, arrange to repair the automation as
soon as possible.
7.2 – Manually releasing and locking
The gearmotor is equipped with a mechanical system that allows for
opening and closing the door manually.
Manual operation must be performed in the case of a power outage or in
the event of anomalies affecting the system.
1 Pull the release cord down until you hear the carriage being released.
2 The door can now be moved manually.
The activation of the manual release may cause an uncontrol-
lable movement of the door if the springs are weak or broken, or
if the door is off-balance.
To restore the functionality of the automation system, move the door
back in position until you hear the carriage being engaged.
In the event of a gearmotor fault, it is still possible to try release the motor
to check whether the fault lies in the release mechanism.
7.3 – User-admissible maintenance operations
The operations that the user must carry out periodically are listed below:
• Cleaning of the surfaces of the devices: use a slightly damp (not
wet) cloth. Do not use substances containing alcohol, benzene,
USER MANUAL (to be delivered to the end user)
the gearmotor
thinners or other flammable substances; the use of these sub-
stances may damage the devices and cause fires or electric
shocks.
• Removal of leaves and stones: disconnect the power supply
before proceeding, so as to prevent anyone from moving the
door.
7.4 – Replacing the transmitter battery
When the battery is flat, the transmitter capacity is significantly reduced.
If, when a button is pressed, the relevant Led turns on then immediately
fades and turns off, it means that the battery is completely flat and should
be immediately replaced.
If instead the Led turns on only for a moment, it means that the battery is
partially flat; the button must be kept pressed for at least half a second for
the transmitter to attempt to send the command.
However, if the battery level is too low to complete the command (and
possibly wait for the response), the transmitter will turn off and the rel-
evant Led will fade. In these cases, normal transmitter operation can be
restored by replacing the battery with another of the same type, while
observing the relevant polarity. To replace the battery, proceed as shown
below.
1
3
Batteries contain polluting substances: do not dispose of them
together with common waste but use the methods set forth in the
local regulations.
7.5 – Lamp replacement
Before proceeding, disconnect AVIO500 from the power supply.
1 Unscrew screw [A] and push button [B], to open the lid.
2 Push the lamp up and rotate to remove. Insert a new 12V / 10W lamp
with BA15 socket.
A
B
2
4
English – 23