Melitta AROMA SIGNATURE Mode D'emploi page 17

and the power cable away from
children under 8 years of age.
• The appliance may be used by
persons with reduced physical,
sensory or mental abilities or lack
of experience and/or knowledge if
they are supervised or have been
instructed in the safe use of the
appliance and have understood
• The appliance is pre set at Level I for water with a high
the potential hazards.
degree of hardness.
• If you have softer water in your household and therefore
• Children must not play with the
need to descale less often, then the descaling indicator can
uctions
be set accordingly.
appliance
• To do this, press the button DECALC ( ) and hold it in
• Replacement of the power cable
(e.g.
for longer than 2 seconds. The red LED starts to flash. At
ot -
the pre set level I (high water hardness) the LED flashes
and all other repairs may only be
once and then pauses (
• You can set the water hardness to 2 other levels. When
carried out by Melitta
e the
you press the button DECALC again the indicator changes
to the LED flashing twice (
Service or by an authorised repair
ontact
and the LED flashes 3 times (
shop.
• The table below shows the settings and the number of
ods
times the indicator flashes.
2. Before using for the first time Hardness setting
• Rinse the appliance before using it for the first time.
° dH
s.
Operate it one time with the full amount of water
but without coffee or a coffee filter.
LED flash rhythm
g
• Decide how long you want the power cable to be by
(DECALC button)
titude
storing the excess cable in the storage on the base
y are
• Ask your local water provider for the hardness level of
of the appliance. .
or
your water or measure it yourself with a water hardness
• Connect the appliance to the power supply.
ow the
measuring strip available in the shops.
• Fill the water tank with fresh, cold water up to the
• When you have set the water hardness at the required
highest water level indicator . The tank light will
d simi-
level, press the DECALC button again and hold it down for
come on (see also 'using the appliance').
or
longer than 2 seconds. Your settings are now correctly pro-
• Insert the glass jug with the lit on, into the appliance
rties
grammed.
under the filter .
t Please note:
• Press the Start & Stop button .
• You cannot programme or change water hardness levels
• Allow the water to flow through the filter into the pot.
all
while brewing coffee.
• For optimal coffee enjoyment and for ease of use,
• The descaling indicator will illuminate when the appliance is
the appliance is equipped with various additional
turned on, if the appliance was switched off without desca-
features. These features can be set individually.
ling after brewing. The LED will only switch off after the
descaling process is complete. (see point 5)
-
2.1 Setting the hotplate
• The water hardness level chosen last remains active even if
the power cable is removed from the socket.
Keeping coffee warm on the hotplate changes the taste
wer.
3.2 Setting the hotplate
be in of your coffee. To avoid this you should enjoy your
coffee fresh, by drinking it as soon after brewing as
Keeping coffee warm on the hotplate changes the taste of
in
possible. Unnecessary warming also uses valuable
your coffee. To avoid this you should enjoy your coffee fresh,
energy. The factory settings for the appliance are for by drinking it as soon after brewing as possible. Unnecessary
warming also uses valuable energy. The factory settings for
30 minutes of warming. This time can be changed as
the appliance are for 30 minutes of warming. This time can be
needed.
changed as needed.
• To change the warm keeping time press the Start &
ut
• To change the warm keeping time press the Start & Stop
Stop button  for longer than 2 sec. The green LED
button for longer than 2 sec. The green LED starts to
starts to flash and the water tank is illuminated.
sto-
flash and the water tank is illuminated.
• The table below shows the settings and the number
he
• The table below shows the settings and the number of
of times the indicator flashes.
times the indicator flashes.
Warming time
ighest
LED flash rhythm
(see
(Start-Button)
under
• Set the desired warming time by briefly (< 2 sec.) pressing
the Start & Stop button
• To confirm, press the Start & Stop button and hold
ot.
).
■
Customer
®
). Press the button again
■■
).
■■■
I II
>21°dH 12-20°dH
■ ■ ■■ ■■ ■■■
30 Min. 60 Min.
■ ■ ■■ ■■ ■■■
until the desired time is displayed.
• Set the desired warming time by briefly (< 2 sec.)
pressing the Start & Stop button until the desired
time is displayed.
• To confirm, press the Start & Stop  button and
hold (> 2 sec.). The warming time is now programmed.
• The setting chosen last remains active even if the
power cable is removed from the socket.
2.2 Setting the end of brewing signal
- only AromaSignature
With the AromaSignature
GB
is indicated by a sound signal. There are two volume
settings (loud / quiet) or you can turn the sound off
Manual_Signature_1013_Layout 1 15.10.13 08:59 Seite 14
completely.
• Press the 2-5 Cups button  longer than 2 sec. The
LED starts to flash.
• The table below shows the settings and the number
GB
of times the indicator flashes.
Sound Signal
LED flash rhythm
(2-5 cups button)
• Press the 2-5 cups button
• Press the 2-5 cups button  repeatedly until the
volume is reached. After each press of the button you will
desired volume is reached. After each press of the
hear the sound signal.
button you will hear the sound signal.
• Press the 2-5 cups button
• Press the 2-5 cups button  longer than 2 sec to
the chosen volume.
confirm the chosen volume.
III • The setting chosen last remains active even if the • The setting chosen last remains active even if the power
cable is removed from the socket.
power cable is removed from the socket.
0-12°dH
4. Coffee preparation
3. Coffee preparation
For the best tasting coffee
■■■
For the best tasting coffee
• Use Melitta ®
• Use Melitta
re use , so that it sits perfectly in the filter.
before use , so that it sits perfectly in the filter.
• If you are using whole beans, grind them fresh as needed.
• If you are using whole beans, grind them fresh as
• If you use ground coffee: Keep the pack tightly closed and
needed.
store it in the fridge.
• If you use ground coffee: Keep the pack tightly closed
and store it in the fridge.
4.1. Using the appliance
• The appliance has to be in the standby position (Eco-
3.1 Using the appliance
Switch at position 'I')
• Remove the lid from the water tank. Fill the tank with cold,
• Remove the lid from the water tank. Fill the tank
clean water. Choose the correct amount of water using the
with cold, clean water. Choose the correct amount
cup or litre level indicators on the tank
of water using the cup or litre level indicators on
water is poured into the tank, it is illuminated making it
the tank . As soon as water is poured into the
easier to see the level indicator marks.
tank, it is illuminated making it easier to see the level
• Remove the filter from the holder using the lever in the fil-
indicator marks.
ter handle
• Remove the filter from the holder using the lever in
• Put a coffee filter into the filter. Add enough ground coffee
the filter handle . Remove the lid from the filter.
for the desired number of cups
• Put a coffee filter into the filter. Add enough ground
• Replace the filter lid. Push the filter back into the holder
coffee for the desired number of cups.
until you hear it click into place
• Replace the filter lid. Push the filter back into the
• Start brewing by pressing the Start & Stop button
holder until you hear it click into place .
LED illuminates and brewing begins.
• Start brewing by pressing the Start & Stop button .
• Aroma Signature DeLuxe: For the best aroma when
The LED illuminates and brewing begins.
making less than 6 cups, start the appliance in '2-5 cup'
• AromaSignature
mode . First press the 2-5 cups button
when making less than 6 cups, start the appliance in
Start & Stop button
'2-5 cup' mode . First press the 2-5 cups button 
giving you the best aromatic coffee result even with small
and then the Start & Stop button . This extends
amounts of coffee.
the brewing time giving you the best aromatic coffee
• At the end of the brewing the tank illumination turns itself
result even with small amounts of coffee.
off. After the chosen warm keeping time (see point 3.2) the
• At the end of the brewing the tank illumination turns
90 Min.
appliance automatically turns off and goes into stand by
itself off. After the chosen warm keeping time the
mode.
appliance automatically turns off.
■■■
• Aroma Signature DeLuxe: The end of brewing is indi-
• AromaSignature
cated by a sound signal.
• After brewing you can remove the pot from the appliance.
The drip stop
DeLuxe the end of brewing
®
loud quiet
■ ■ ■■ ■■
repeatedly until the desired
longer than 2 sec to confirm
coffee filters 1x4 ® . Fold the coffee filter befo-
coffee filters 1x4 . Fold the coffee filter
® ®
.
. Remove the lid from the filter.
.
.
DeLuxe: For the best aroma
®
. This extends the brewing time
DeLuxe: The end of brewing is
®
prevents dripping onto the hotplate.
DeLuxe
®
• Atte
off
time
the
■■■ ■■■
• The
• Whe
LED
• Aro
noti
• The
by m
• Afte
thro
rem
6. Cl
• Befo
GB
Swit
• Nev
• Clea
• Clea
pot,
• Filte
in th
• The
clean
. As soon as
7. Di
• Plea
rega
• Pack
use
. The
and then the
17