Multiplex PARTENAVIA P.68 Instructions De Montage page 25

User Manual of Brushless Speed Controller
Trouble Shooting
Trouble
After power on, motor does not work, no sound is
emitted
After power on, motor does not work, such an alert
tone is emitted: "beep-beep-, beep-beep-,beep-
beep-" (Every "beep-beep-" has a time interval of
about 1 second)
After power on, motor does not work, such an alert
tone is emitted: "beep-, beep-, beep- "(Every "beep-"
has a time interval of about 2 seconds)
After power on, motor does not work, such an alert
tone is emitted: "beep-, beep-, beep-" (Every "beep-"
has a time interval of about 0.25 second)
After power on, motor does not work, a special tone
" 56712" is emitted after 2 beep tone (beep-beep-)
The motor runs in the opposite direction
Program the ESC with your transmitter (4 Steps)
Note: Please make sure the throttle curve is set to 0 when the throttle
stick is at bottom position and 100% for the top position.
1. Enter program mode
2. Select programmable items
3. Set item's value (Programmable value)
4. Exit program mode
1. Enter program mode
1) Switch on transmitter, move throttle stick to top position,
connect the battery pack to ESC
2) Wait for 2 seconds, the motor should emit special tone like
"beep-beep-"
3) Wait for another 5 seconds, special tone like " 56712"
should be emitted, which means program mode is entered.
3. Set item value (Programmable value)
You will hear several tones in loop. Set the value matching to a tone by moving throttle stick to
top when you hear the tone, then a special tone " 1515" emits, means the value is set and
saved. (Keeping the throttle stick at top, you will go back to Step 2 and you can select other
items; or moving the stick to bottom within 2 seconds will exit program mode directly)
"beep-"
Tones
Items
1 short tone
Brake
Battery type
Cutoff mode
Cutoff threshold
Start mode
Timing
- The connection between battery pack
and ESC is not correct
- Input voltage is abnormal, too high or
too low
- Throttle signal is irregular
- The throttle stick is not in the bottom
(lowest) position
- Direction of the throttle channel is
reversed, so the ESC has entered the
program mode
- The connection between ESC and the
motor need to be changed
"beep-beep-"
2 short tones
Off On
Lipo NiMH
Soft-Cut Cut-Off
Low Medium
Normal Soft
Low Medium
Possible Reason
2. Select programmable items
After entering program mode, you will hear 8 tones in a loop with the
following sequence. If you move the throttle stick to bottom within 3
seconds after one kind of tones, this item will be selected.
1. "beep"
2. "beep-beep-"
3. "beep-beep-beep-"
4. "beep-beep-beep-beep-" cutoff threshold
5. "beep-----"
6. "beep-----beep-"
7. "beep-----beep-beep-"
8. "beep-----beep-----"
Note: 1 long "beep-----" = 5 short "beep-"
"beep-beep-beep"
3 short tones
High
Super soft
High
Action
- Check the power connection
- Replace the connector
- Check the voltage of battery pack
- Check the receiver and transmitter
- Check the cable of throttle channel
- Move the throttle stick to bottom
position
- Set the direction of throttle channel
correctly
- Swap any two wire connections between
ESC and motor
brake (1 short tone)
battery type (2 short tone)
cutoff mode (3 short tone)
(4 short tone)
startup mode (1 long tone)
timing (1 long 1 short)
set all to default (1 long 2 short)
exit (2 long tone)
4. Exit program mode
There are 2 ways to exit program
mode:
1. In step 3, after special tone
" 1515", please move throttle
stick to the bottom position within
2 seconds.
2. In step 2, after tone "beep----
-beep-----"(th at is: The item #8),
move throttle stick to bottom
within 3 seconds.
EN
25