Specifications - Hameg Instruments HM 400 Manuel

40 MHz Analog Oscilloscope HM400
All data valid at 23 °C after 30 minutes warm-up.
Vertical Deflection
Operating Modes: Channel 1 or 2 only
Channels 1 and 2 (alternate or chopped)
Sum or Difference of CH 1 and CH 2
Invert:
CH 2
XY Mode: CH 1 (X) and CH 2 (Y)
Bandwidth (-3 dB):
0...40 MHz
DC, 5 mV/div....20 V/div.:
AC, 5 mV/div....20 V/div.: 2 Hz...40 MHz
DC, 1...2 mV/div.: 0...10 MHz
2 Hz...10 MHz
AC, 1...2 mV/div.:
Rise Time (calculated): <35 ns (1...2 mV/div.)
<8.75 ns (5 mV/div....20 V/div.)
Deflection Coefficient: 1–2–5 Sequence
±5 % (1...2 mV/div.)
±3 % (5 mV/div....20 V/div.)
Variable (uncalibrated): >2.5:1 to >50 V/div.
Input Impedance: 1 MΩ II 15 pF
Input Coupling: DC, AC, GND (ground)
Max. Input Voltage: 400 V (DC + peak AC)
Triggering
Automatic: Linking of peak detection and trigger level
Min. signal height 0.5 div.
Frequency range 5 Hz...50 MHz
Level control range From peak- to peak+
Normal (without peak):
Min. signal height 0.5 div.
Frequency range 0...50 MHz
Level control range
-10....+10 div.
Slope: Rising or falling
Sources: Channel 1 or 2, Line and External
Coupling: AC (5 Hz...80 MHz),
DC (0...80 MHz),
LF (0...1.5 kHz)
Trigger Indicator: LED
External Trigger:
Input Impedance: 1 MΩ II 15 pF
External Trigger Signal: 0.3 V
DC (0...50 MHz),
AC (20 Hz...50 MHz)
Max. input voltage:
100 V (DC + peak AC)
Active TV sync. separator: Field and Line, +/-
Horizontal Deflection
Time Base:
100 ns/div.....0.2 s/div (1–2–5 Sequence)
Accuracy: ±3 %
Variable (uncalibrated): >2.5:1 to >1.25 s/div.
X Magnification x10: up to 10 ns/div.
Accuracy: ±5 %
Hold-Off Time: variable to approx. 10:1
XY
Bandwidth X amplifier: 0...2.5 MHz (-3 dB)
XY Phase shift <3°: <120 kHz
Operation/Readout/Control
Manual: via controls and buttons
Autoset: automatic signal related parameter settings
Save and Recall: 6 instrument parameter settings
Component Tester

Specifications

Test Voltage: approx. 7 V
Test Current: max. 7 mA
Test Frequency: approx. 50 Hz
Test Connection: 2 banana jacks 4 mm Ø
One test circuit lead is grounded
via protective earth (PE)
Miscellaneous
CRT: D14-363GY, 8 x 10 div. with internal graticule
Acceleration Voltage: approx. 2 kV
Trace Rotation: adjustable on front panel
Z-Input (Intens. modulation): max. +5 V (TTL), 10 kHz
Probe ADJ Output: 1 kHz/1 MHz Square Wave Signal approx.
0.2 V
Power Supply (Mains): 105...253 V, 50...60 Hz ±10 %, CAT II
Power Consumption: approx. 30 W at 230 V/50 Hz
Safety class: Safety class I (EN61010-1)
HM400E/180112 · C&E · Subject to change without notice · © HAMEG Instruments GmbH
HAMEG Instruments GmbH · Industriestr. 6 · D-63533 Mainhausen · Tel +49 (0) 6182 8000 · Fax +49 (0) 6182 800100 · www.hameg.com · info@hameg.com
≤5 V,
pp
(open circuit)
rms
(short-circuit)
rms
(tr <5 ns) for probe adjustment
pp
Operating temperature: +5...+40 °C
Storage temperature: -20...+70 °C
Rel. humidity: 5...80 % (non condensing)
Dimensions (W x H x D): 285 x 125 x 380 mm
Weight: approx. 4.8 kg
Accessories supplied: Line Cord, Operating Manual, 2 Probes 1:1/10:1 (HZ154)
with LF/HF adjustment, CD
+5 °C...+40 ° C
Recommended accessories:
HZ20 Adapter, BNC to 4 mm banana
HZ33 Test cable 50 Ω, BNC/BNC, 0.5 m
HZ34 Test cable 50 Ω, BNC/BNC, 1 m
HZ45 19"-Rackmount Kit 4RU
HZ51 Probe 10:1 (150 MHz)
HZ52 Probe 10:1 RF (250 MHz)
HZ53 Probe 100:1 (100 MHz)
HZ100 Differential probe 20:1/200:1
HZ109 Differential probe 1:1/10:1
HZ115 Differential probe 100:1/1000:1
HZ200 Probe 10:1 with auto attenuation ID (250 MHz)
HZ350 Probe 10:1 with automatic identification (350 MHz)
HZ355 Slimline probe 10:1 with automatic identification (500 MHz)
HZO20 High voltage probe 1000:1 (400 MHz, 1000 V
HZO30 Active probe 1 GHz (0.9 pF, 1 MΩ, including many accessories)
HZO50 AC/DC Current probe 20 A, DC...100 kHz
HZO51 AC/DC Current probe 1000 A, DC...20 kHz
® · DQS-certified in accordance with DIN EN ISO 9001:2008, Reg.-No.: 071040 QM08
S p e c i f i c a t i o n s
)
rms
Subject to change without notice
27