Black & Decker BCRT8I Traduction De La Notice D'instructions Originale page 11

Turn the collet nut (8) clockwise to tighten the collet nut (8)
u
securely onto the accessory mandrel.
Note: The collet (7) was designed to be hand tightened and
loosened only. Accessories naturally self tighten during use.
A wrench is provided with the tool for loosening. You should
never need to tighten the collet nut (8) with a wrench. If a
wrench is needed, use only the wrench provided. Do not use
tools that will mar the finish and could break the collet. Always
ensure there is some accessory in the collet before tightening.
Tightening an empty collet can crack it.
When finished, release the spindle lock button (6).
u
Note: If an accessory causes vibration it can usually be
improved by loosening the collet nut (8) , pushing the
accessory in as far as it will go and rotating it 1/4 turn then
retightening the collet (7).
Operation
@
Warning! To reduce the risk of serious personal
injury, keep away from the ON/OFF button while
making any adjustments or removing/installing
attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. D) @
Warning! To reduce the risk of serious personal
injury, ALWAYS use proper hand position as
@
shown.
Warning! To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
There are two ways to hold the rotary tool, grip the main
handle (2) like a pencil between your thumb and forefinger or
holding by grasping the main handle (2) in your palm.
LED Worklight
@
Warning! When using the worklight for purposes
other than intended, be sure to remove all acces-
sories. Unused accessories could cause injury or
@
property damage.
Warning! Do not stare into the LED. Serious eye
injury could result.
When the tool is activated by depressing the ON/OFF button
(1) , the LED work light (9) will automatically turn on. The LED
work light will turn off when the tool is turned off.
Turning Tool On and Off
@
Warning! Because this tool has a separate
speed wheel (3) for setting the speed (3,500
- 29,500 rpm), the tool will start at the speed
where the speed wheel is set.
(Original instructions)
To turn the tool on, depress the ON/OFF button (1). The
u
tool will immediately run at the speed which is selected.
Note: Do not attempt to start tool with spindle lock engaged.
It will not run.
To turn the tool off, depress the ON/OFF button (1) a
u
second time.
Speed Selection (Fig. E)
@
Warning! Because this tool has a separate
speed wheel (3) for setting the speed (3,500
- 29,500 rpm), the tool will start at the speed
@
where the speed wheel is set.
Warning! Never exceed the speed rating of the
accessory being used.
To operate the tool, select the speed setting you wish with
u
the speed wheel (3), shown in Fig. E, and depress the
ON/OFF button (1).
The speed setting can be adjusted with the tool on or off.
u
The numbered positions,1 through 5 inscribed on the
u
speed wheel (3), do not indicate any precise speed but
are good reference points. The higher the number, the
higher the tool speed.
The following chart provides approximate speeds at each
setting:
Selected Speed
1
2
3
4
5
Note: Actual rpm's on your tool may vary. Be sure to select
the proper speed for your rotary tool operation.
The following chart provides a speed guide for various
general operations:
Operation
Cutting metal
Deburring metal
Stripping metal
Sharpening metal
Engraving metal
Removing rust
Sanding wood
Polishing
Note: If in doubt about the proper speed for your operation,
test the performance at low speed settings and gradually
increase until a comfortable speed is found.
ENGLISH
RPM
3,500
8,000
12,000
18,500
29,500
Suggested Speed settings
4 - 5
4 - 5
4 - 5
3 - 4
4 - 5
1 - 2
4 - 5
1 - 2
11