Instructions For Installation; Data Plate; Technical Data; Installation - Diamond SF101 Manuel D'installation, Emploi Et Entretien

I.

INSTRUCTIONS FOR INSTALLATION

1.

DATA PLATE

The data plate (see fig. 2) is placed externally on the left side panel of the appliance.
2.

TECHNICAL DATA

Models:
ambient cupboard support
heated cupboard support
External dimensions:
- width:
- depth:
- height:
Power supply:
Frequence:
Absorbed electric power:
Cable cross section area:
Information regarding acoustic emission: the noise emission level of the functional components of these appliances does not
exceed 70 dB (A).
3.

INSTALLATION

Important! The heated cupboard elements must be installed
in accordance with the specific oven range. The manufacturer
declines any responsibility if this provision is not observed.
3.1

INSTALLATION PLACE

The simple or cupboard (heated or ambient) oven support units,
used for 6-10 GN1 /1 and 10GN2/1 versions, cover the base
perimeter of the appliance, therefore:
• Install the appliance only in adequately ventilated premises.
• Connect the appliance according to the regulations in force
(Gas Safety (Installation and Use) Regulations, 1984; Health
and Safety at Work Act, 1974; Codes of Practice BS 6173, 1982;
The Building Regulations, 1985; The Building Standards
Regulations, 1981).
3.2 POSITIONING (fig. 1, 1A)
• Disassemble the rear panel and control panel (if expected).
• Position the oven on the base support after having previously
removed the four feet.
• Before positioning the 10GN2/1 oven on the heated or ambient
cupboard support, remove the lower central screw of the right
and left side of the oven.
• Before installing the oven on the ambient cupboard, assemble
the drawer on the bottom of the appliance as follows:
Insert 4 tongues "L" (fig. 8) for the drawer support into the 4
holes (placed on right hand side) of the oven bottom and fix it
into slot "H" (fig.8), by means of a self-tapping screw Ø 4,3
(position "1").
Assemble panel "P" (if the retractable shower-head installation
is not expected) by inserting the pins into housing of the the
oven bottom and fix it with the self-tapping screw (position "2").
• Fix the oven to the support by screwing M5x14 screws into the
corners. Access can be gained from the rear side, the technical
compartment placed under the door and the hole of the control
panel or drawer (fig. 4).
5958.643.- -
10 GN1/1
922109
922118
922163
922112
922124
922167
922023°
mm 890
mm 807
mm 850(+25:-30)
V 220...230 ~
Hz 50
kW 2,55
mm 2 3 x 1,5
(°) Model with weels.
• Reassemble the disassembled components.
• The left side surface of the appliance must have a 50 cm
distance from the other surfaces to carry out maintenance
operations; the rear side and the right one must have a 5 cm
distance from the other surfaces.
• The appliance is not suitable for built-in installation.
WARNINGS
• For the overall dimensions and the dimensions necessary for
the connection, see technical data and figures on the first
pages of this instruction manual.
• Position the appliance and adjust the height of the work top by
screwing or unscrewing the adjustable feet, if necessary.
• Remove the protective film from the external panels of the
appliance. Should this not happen, use an appropriate diluent.
• The installation and maintenance (gas, electric current) must
only be carried out by the supply body or an authorized
installer.
3.3

OVEN ACCESSORIES

3.3.1 Oven supports (figs. 1B - 1C) (accessory)
Mod. 6GN1/1 (electric and gas)
Mod. 10GN1/1 (electric and gas)
Mod. 10GN2/1 (electric and gas)
(*) only for gas models equipped with boiler
(°) Model with weels.
The oven support has already been assembled in order to be
joined to the appliance. Therefore, disassemble the four existing
feet from the oven and replace them with the support.
Position the unit and adjust the height of the loading top of the
oven, if expected, by screwing or unscrewing the adjustable feet.
3.3.2 Runner supports for grids (fig. 4) (accessory)
Mod. 6GN1/1 (electric and gas)
Mod. 10GN1/1 (electric and gas)
Mod. 10GN2/1 (electric and gas)
8
10 GN2/1
922110
922119
922164
922113
922125
922168
890
1044
850(+25:-30)
220...230~
50
2,55
3 x 1,5
922101 922100*
922102 922114°
922103
922105
922106
922107