Wall Showerhead; Concealed Showerhead; Electric Connection; Installation Of The Power Supply Cable - Diamond SF101 Manuel D'installation, Emploi Et Entretien

Assemble the grid supports "N" in the desired position. Place the
fixing pins "F" on the upper and lower holes drilled on the bottom
of the unit.
3.3.3 Wall showerhead (fig. 5) (accessory)
This accessory with code 922171 is suitable on all mentioned
oven models, it can be installed as shown in fig. 5.
• Drill 3 holes ø 3 on the left side panel of the oven by using, as
point of reference, the support of the showerhead "S" (which
must be fixed with 3 self-tapping screws 3,5x13 by respecting
the center distance).
• Drill 2 holes ø 6 on the stud to fix the cock, by respecting the
center distance.
3.3.4 Concealed showerhead (fig. 6) (accessory)
This accessory with code 922170 is suitable on all mentioned
oven models, it must be installed on the bottom of the oven in
correspondence to the 3,5 mm holes drilled before, which permit
the fixing with self-tapping screws "Af" (4.2x13) (fig. 6).
It is to be positioned:
- On the technical compartment by disassembling the small
panel "T" (figs. 1-1A) when positioned into a cupboard unit for
10GN1/1 and 10GN2/1 models. The access can be gained by
removing the drawer or control panel from the right side and
from the technical compartment for the left side. It is suggested
to assemble the kit before installing the oven on the cupboard
support.
- On the bottom of the appliance on the right side of 6GN1/1
models.
- The showerhead kit must be connected to the water power
supply with the flexible pipe supplied.
Note:
- The accessory can be assembled on all oven units even if they
are assembled on the table.
4.

ELECTRIC CONNECTION

• The connection to the supply mains must be carried out
according to the standards in force.
• Before carrying out the electric connection make sure the
voltage and frequency on the data plate correspond with that
of the power supply.
• The electric connection is to be carried out according to the
enclosed electric diagram or as shown in the data plate placed
near the connection terminal board.
• The appliance is to be connected to the power supply in a
permanent way. The connection must be carried out with a H05
RN-F type cable. A multipolar switch must be placed between
the appliance and the mains, whith a contact opening distance
of 3 mm and an appropriate capacity (for ex. magnetothermic
switch).
This switch must be installed in the building's permanent
electrical system and near the appliance.
The power supply cable must be installed in a metal or rigid
plastic pipe. Should the connection be carried out through an
existing wire, the installation pipe must not be placed inside the
appliance. Furthermore, be careful there are no burrs on the
pipe.
• The appliance is to be connected to an earth outlet. For this
purpose, there is a screw marked G near the connection
terminal board to which the earth wire is to be connected. The
appliance must be included in an equipotential system.
This connection is carried out with a setscrew marked E placed
under the appliance. The equipotential wire must have a 10
mm 2 section.
4.1

INSTALLATION OF THE POWER SUPPLY CABLE

Place a three-pin plug fitted for the load of the appliance to the end
of the power supply cable or connect it to a cutoff device.
5958.643.- -
The manufacturer declines any responsibility if the accident
prevention standards are not observed.
5.

CONNECTION TO THE WATER SYSTEM

Connect the water inlet pipe "A" to the distribution network by
means of a mechanical filter and cutoff cock. Before connecting
the filter, let a certain quantity of water flow in order to drain the
pipe from any ferrous slags.
• The water inlet for the humidification must be supplied with
drinking water and a pressure value between 150 " 250 kPa
(1,5"2,5 bar).
5.1 CONDENSATE DRAINAGE SYSTEM (fig. 1)
The drainage of the heated chamber must flow into a dripping tray
"V" (fig. 1) which must be periodically emptied.
6.

START UP SYSTEM

Before starting the appliance, connect the main switch of the
electric system and open the water cutoff cock by following the
instructions for use at par. 3.
7.

SAFETY DEVICES

The appliance is equipped with the following safety devices:
7.1 Safety thermostat for heated chamber (fig. 7)
It intervenes by disconnecting the heating with manual reset.
Access can be gained by removing the box with control panel so
as to reset the thermostat push button "T" placed externally on the
heated chamber.
7.2 The appliance is equipped with one fuse "F" (fig. 7) (5AF,
rapid action with an interruption power level of 35A) protecting the
auxiliary circuit, see electrical diagram. It is placed behind the
control panel. To replace it, unscrew the locating cap and replace
the damaged component with one that has the same rating; this
value is indicated on the data plate located near the fuse.
8.

CHECKING THE OPERATION

• Turn ON the appliance following the instructions for use.
• Instruct the user on the operation and servicing of the appliance
informing him to observe the warnings for a correct use.
9.

SERVICING

The components which may require normal servicing can be
accessed by opening the control panel and the rear panel.
10.

PROBLEMS AND SOLUTIONS

Malfunctions may occur also during the normal operation of the
appliance.
- The heating of the heated chamber does not ignite or is
ineffective.
Causes:
• Temperature limit switch of the heated chamber has intervened.
• Resistance is damaged.
• Relay coil relative the damaged elements is damaged.
• Thermostatic probe is damaged.
• Thermostat is damaged.
9
(fig. 1)