Brush Cleaning; Brush Removal/Fitting; Squeegee Cleaning; Ordinary Maintenance - ADIATEK baby-e 11 2011 Emploi Et Entretien

GB

BRUSH CLEANING

Remove the brush and clean it with a water jet (for
the disassembly see under "BRUSH REMOVAL/ FIT-
TING").

BRUSH REMOVAL/FITTING

1. Tip the machine over backwards (see under "VER-
TICAL POSITIONING OF THE MACHINE") paying atten-
tion to remember to switch off the machine pressing
all the switches and take off the plug from the mains
socket.
2. With the machine in this position rotate the
brush clockwise, as indicated in the figure, until it is
released from their seats of the brush holder plate.
3. To reassemble the brush insert the coupling but-
tons into the slots of the brush holder plate and ro-
tate counterclockwise until it locks.
ATTENTION:
The handling of the brush operation must be carried
out wearing suitable gloves to protect both mechan-
ically from contact with the bristles and the chemi-
cal risk of contact with dangerous solutions.

SQUEEGEE CLEANING

Keeping the squeegee clean guarantees the best dry-
ing action.
1. Tip over the machine backwards (see under "VER-
TICAL POSITIONING OF THE MACHINE") paying atten-
tion to remember to switch off the machine pressing
all the switches and take off the plug from the mains
socket.
2. With the machine in this position take care to
clean both the rubber squeegee blades and particu-
larly the suction inlet. Also remove any fibres (string
or hair) that can prevent the support turning freely.

ORDINARY MAINTENANCE

BRUSH REPLACEMENT

The brush has to be replaced when the bristles have
reached a length of 10 mm. It is possible to use also
other brush types, depending on the type and dirt of
floor to be cleaned (see under "RECOMMENDED
BRUSHES").
Remove the old brush and replace it with a new one
(see under "BRUSH REMOVAL/FITTING").

REAR SQUEEGEE RUBBER REPLACEMENT

Check the squeegee rubber wear and eventually turn
or replace it.
For the replacement it is necessary to:
1. Lower the squeegee by lowering the handle lever
(4) placed in the centre of the handle bar.
2. Tip over the machine backwards (see under "VER-
TICAL POSITIONING OF THE MACHINE") paying atten-
tion to remember to switch off the machine pressing
all the switches and take off the plug from the mains
socket.
3. With the machine in this position release the
wing nuts (1) unscrewing them completely to free
the squeegee.
4. Take off the coupling (2) of the squeegee hose
and take off the squeegee.
5. Release the catch (4) of the rubber blade clamp
and take the rubber off to turn it to a new side or
replace it.
19
6. Check that the coupling and the squeegee hose
are not obstructed and if necessary, clean the entire
assembly.
To reassemble the squeegee reverse the operations
above.

FRONT SQUEEGEE RUBBER REPLACEMENT

Check the wear of the front squeegee rubber and re-
place it if worn out.
For the replacement it is necessary to:
1. Lower the squeegee by lowering the handle lever
(4) placed in the centre of the handle bar.
2. Tip over the machine backwards (see under "VER-
TICAL POSITIONING OF THE MACHINE") paying atten-
tion to remember to switch off the machine pressing
all the switches, take off the plug from the mains
socket and empty the tanks.
3. With the machine in this position take off the
squeegee and then the rear squeegee rubber (see
under "REAR SQUEEGEE RUBBER REPLACEMENT").
4. Take off the wing nuts (6) in the upper part of
the squeegee body.
5. Separate the two metal parts that form the
squeegee body to take off the front rubber.
6. Clean all the components with water.
To reassemble the squeegee reverse the operations
above.
GB